| 2-ETHYLHEXYL |
2-ETHYLHEXYL ACRYLATE |
ACR |
Acrylic ester used for polymer manufacturing and as a raw material for
syntheses.
Molar Mass(g/mol): 184.28
Chemical formula:
Stoichiometric formula: C11H20O2
CAS number: 103-11-7 |
| ACRALEN |
ACRALEN™ SNX 7675 |
OTH |
ACRALEN SNX 7675 ia an aqueous emulsion of a self-crosslinking styrene-butadiene-acrylonitrile copolymer. |
| ACRYLIC |
ACRYLIC ACID - STABILIZED |
ACR |
Non-saturated organic acid used for polymer manufacturing and as a raw material for syntheses.Molar Mass(g/mol): 72.06Chemical formula: Stoichiometric formula: C3H4OCAS number: 79-10-7 |
| ACRYLIC |
ACRYLIC ACID - STABILIZED - PURE |
ACR |
Non-saturated organic acid used for polymer manufacturing and as a raw
material for syntheses.
Molar Mass(g/mol): 72.06
Chemical formula:
Stoichiometric formula:
C3H4O2 CAS number: 79-10-7 |
| ALCOTEX |
ALCOTEX™ 234 |
OTH |
Synthomer Ltd has developed Alcotex 234 for use in conjunction with Alcotex 225 as a buildup suppressant for vinyl chloride suspension polymerisation. It eliminates build-up on the reactor baffles and stirrer or areas of poor surface quality. Use of Alcotex 234 will lead to a substantially higher number of production runs before the reactor has to be opened and pressure cleaned. This results in higher productivity rates and a better quality PVC resin. |
| ALCOTEX |
ALCOTEX™ 432P |
PVOH |
Alcotex 432P is a 43% hydrolysed polyvinyl alcohol supplied as a low viscosity methanol based solution. It has been specifically developed by Synthomer Limited as a secondary suspending agent for vinyl chloride suspension polymerisation.
It may be used in conjunction with conventional primary suspending agents. In optimised recipes, improvements can be obtained in the porosity/bulk density relationship. Better porosity facilitates both monomer removal and plasticiser uptake. These criteria are further enhanced when Alcotex 432P is used with the Alcotex range of primary suspending agents. |
| ALCOTEX |
ALCOTEX™ 45 |
PVOH |
Alcotex 45 is a 45% hydrolysed polyvinyl alcohol supplied as a low viscosity solution in a water/isopropyl alcohol solution. It has been specifically developed as a secondary suspending agent for vinyl chloride suspension polymerisation. It may be used in conjunction with conventional primary suspending agents. In optimised recipes, improvements can be obtained in the porosity/bulk density relationship. Better porosity facilitates both monomer removal and plasticiser uptake. These criteria are further enhanced when Alcotex 45 is used with the Alcotex range of primary suspending agents.
NMR measurements have shown that Alcotex 45 has a random distribution of acetate groups. |
| ALCOTEX |
ALCOTEX™ 55-002H |
PVOH |
Alcotex 55-002H is a colloidal dispersion of polyvinyl alcohol. It has been specifically developed by Synthomer Ltd as a secondary suspending agent for vinyl chloride suspension polymerisation. It may be used in conjunction with conventional primary suspending agents. In optimised recipes, improvements can be obtained in the porosity/bulk density relationship. Better porosity facilitates both monomer removal and plasticiser uptake. These criteria are further enhanced when Alcotex 55-002H is used with the Alcotex range of primary suspending agents.
NMR measurements have shown that Alcotex 55- 002H has a random distribution of acetate groups. |
| ALCOTEX |
ALCOTEX™ 552P |
PVOH |
Alcotex 552P is an aqueous solution of a 55% hydrolysed polyvinyl alcohol. It has been developed by Synthomer Ltd as a porosity enhancement agent for PVC suspension polymerisation. It has a low residual methanol content. Alcotex 552P can be used in conjunction with conventional primary suspending agents.
In optimised recipes, improvements can be obtained in the porosity/bulk density relationship. Better porosity facilitates both monomer removal and plasticiser uptake. These criteria are further enhanced when Alcotex 552P is used with the Alcotex range of primary suspending agents.
NMR measurements have shown that Alcotex 552P has a random distribution of acetate groups.
|
| ALCOTEX |
ALCOTEX™ 7206 |
PVOH |
Alcotex 7206 is a 72.5% hydrolysed, low/ medium molecular weight polyvinyl alcohol which has been specially developed for use as a primary suspending agent for vinyl chloride suspension polymerisation.
NMR measurements have shown that Alcotex 7206 has a blocky distribution of acetate groups. |
| ALCOTEX |
ALCOTEX™ 80 |
PVOH |
Alcotex 80 is an 80% hydrolysed high molecular weight polyvinyl alcohol which has been specially developed for use as a primary suspending agent for vinyl chloride suspension polymerisation. |
| ALCOTEX |
ALCOTEX™ 864 |
PVOH |
Alcotex 864 is a polyvinyl alcohol, internally plasticized and supplied in a water solution. Alcotex 864 has a medium high hydrolysis level and a low molecular weight.
FEATURES
Aqueous solution.
Forms very flexible films when dry.
Dry films can be easily dissolved.
Very receptive to ink jet printing inks.
The dry film can be insolublised by crosslinking.
Non-ionic copolymer.
Alcotex 864 is manufactured on a dedicated polymerisation plant in Harlow, England. |
| ALCOTEX |
ALCOTEX™ 8847 |
PVOH |
Alcotex 8847 is an 88% hydrolysed polyvinyl alcohol for use in speciality applications such as vinyl acetate containing copolymer resins as well as in standard grades.
Alcotex 8847 is a high molecular weight polyvinyl alcohol giving a high colloidal stability in PVC suspension polymerisation. |
| ALCOTEX |
ALCOTEX™ 975 |
PVOH |
Alcotex 975 is an internally plasticized polyvinyl alcohol supplied in a solvent system of water and propan-1-ol. Alcotex 975 has a high hydrolysis level and a medium molecular weight.
FEATURES
Ready to use solution.
Forms very flexible films when dry.
Dry films can be easily dissolved.
Very receptive to ink jet printing inks.
The dry film can be insolublised by crosslinking.
Non-ionic copolymer.
Alcotex 975 is manufactured on a dedicated polymerisation plant in Harlow, England. |
| ALCOTEX |
ALCOTEX™ B72 |
PVOH |
Alcotex B72 is polyvinyl alcohol which has been specially developed for use as a primary suspending agent for vinyl chloride suspension polymerisation. It is manufactured by Synthomer UK Ltd. using our exclusive manufacturing process which has advantages over other manufacturing methods, in that it allows more efficient control over the degree of hydrolysis and particle size of the product.
NMR measurements have shown that Alcotex B72 has a block distribution of acetate groups. |
| ALCOTEX |
ALCOTEX™ WD100 |
PVOH |
Alcotex WD100 is an aqueous solution of a 43% hydrolysed polyvinyl alcohol. It has been specifically developed by Synthomer Ltd as a secondary suspending agent for vinyl chloride polymerisation. Infinitely dilutable in water, and with an extremely low methanol content, Alcotex WD100 offers increased PVC resin porosity and reduced levels of gels or ‘fish eyes’ when compared to traditional products.In optimised recipes, improvements can be obtained in the porosity/bulk density relationship. Better porosity facilitates both monomer removal and plasticiser uptake. These criteria are further enhanced when Alcotex WD100 is used with the Alcotex range of primary suspending agents.
Alcotex WD100 is also compatible with other conventional primary suspending agents.
NMR measurements have shown that Alcotex WD100 has a random distribution of acetate groups.
The data below represents typical values obtained with different batches of Alcotex WD100. |
| AXILAT |
AXILAT™ DF 6352 DD |
OTH |
AXILAT™ DF 6352 DD is a foam control agent based on a mixture of mineral oil and nonionic surfactants on an inert carrier. It is APEO free. |
| AXILAT |
AXILAT™ DF 770 DD |
OTH |
Axilat™ DF 770 DD is a foam control agent based on a mixture of mineral oil and nonionic surfactants on an inert carrier. It is APEO free. |
| AXILAT |
AXILAT™ DF 775 DD |
OTH |
Axilat™ DF 775 DD is a foam control agent based on a mixture of mineral oil and nonionic surfactants on an inert carrier. It is APEO free. |
| AXILAT |
AXILAT™ HP 8510 |
VACO |
Axilat HP 8510 is a vinyl acetate, vinyl versatate copolymer resin in redispersible powder form. It is a highly versatile resin with high redispersibility in water and used in dry mortars. |
| AXILAT |
AXILAT™ HP 8513 |
VACO |
Axilat™ HP 8513 is a vinyl acetate, vinyl versatate
copolymer resin in redispersible powder form. |
| AXILAT |
AXILAT™ HP 8530 |
VACO |
Axilat HP 8530 is a hydrophobic vinyl acetate/vinyl versatate copolymer resin in redispersible powder form. It is a highly versatile resin with high redispersibility in water and used in dry mortars. |
| AXILAT |
AXILAT™ HP 8538 |
VACO |
AXILAT HP 8538 is a redispersible-in-water powder, used in dry mortars to improve adhesion to conventional substrates, especially to polystyrene foam slabs hydrophobic properties mechanical properties workability of fresh mortar. |
| AXILAT |
AXILAT™ PSB 150 |
XSBR |
Axilat ™ PSB 150 is a styrene butadiene copolymer powder resin that is redispersible in water. Axilat PSB 150 redisperses to a particle size that is one-tenth of conventional latex powders, resulting in a very high binder power and enhanced adhesion for end use formulations. It is highly recommended for gypsum-based applications. |
| AXILAT |
AXILAT™ RH 100 XP |
OTH |
Axilat RH 100 XP is a rheological agent for cement and gypsum-based mortars (thixotropy and anti-Segregation). |
| AXILAT |
AXILAT™ RH 200 XP |
OTH |
Axilat RH 200 XP is a rheological agent for cement and gypsum-based mortars (thixotropy and anti-segregation). |
| AXILAT |
AXILAT™ SA 502 |
OTH |
Axilat SA 502 is a 100% amorphous “flash” alumina with a very high surface area. It is a set accelerator and can be used as an anti-shrinkage admixture for Portland cement. |
| AXILAT |
AXILAT™ UP 600 B |
VACO |
Axilat UP 600 B is a vinyl acetate, vinyl versatate and maleic ester copolymer resin in redispersible powder form. It is redispersible in water and used in dry mortars to improve workability of fresh mortar; hydrophobic properties; adhesion to conventional substrates, especially after severe ageing conditions; and mechanical properties (flexibility, abrasion resistance and cohesive strength). It is a plasticiser-free powder, particularly suitable for ecologically demanding systems. |
| AXILAT |
AXILAT™ UP 620 E |
VACO |
Axilat UP 620 E is a vinyl acetate, vinyl versatate and maleic ester copolymer resin in redispersible powder form. It is redispersible in water and used in dry mortars to improve workability of fresh mortar; hydrophobic properties; adhesion to conventional substrates, especially after severe ageing conditions; and mechanical properties (flexibility, abrasion resistance and cohesive strength). It is a plasticiser-free powder, particularly suitable for ecologically demanding systems. |
| Binder |
XA 2461 |
SA |
Binder XA 2461 is a water-based modified acrylic and adipic acid dihydrazide-free binder with good film formation at low VOC. Good balance between hardness and flexibility.It provides excellent blocking and excellent adhesion for durability on masonry and wood surfaces. |
| CHEMIGUM |
CHEMIGUM™ LATEX 248 |
NBR |
Anionic aqueous dispersion of a butadiene-acrylonitrile copolymer |
| CHEMIGUM |
CHEMIGUM® LATEX 550 |
NBR |
Anionic aqueous dispersion of a carboxylated butadiene-acrylonitrile copolymer containing a non-staining, non-discolouring antioxidant |
| CHEMIGUM |
CHEMIGUM™ LATEX 6271 |
NBR |
Anionic aqueous dispersion of a carboxylated butadiene-acrylonitrile copolymer |
| CHEMIGUM |
CHEMIGUM™ LATEX 6387 |
NBR |
Anionic aqueous dispersion of a butadiene-acrylonitrile copolymer containing a non-discolouring antioxidant |
| CHEMIGUM |
CHEMIGUM™ P35 |
NBR-Dry |
Copolymer of butadiene-acrylonitrile partitioned with calcium carbonate |
| CHEMIGUM |
CHEMIGUM™ P615DS |
NBR-Dry |
Copolymer of butadiene-acrylonitrile partitioned with calcium carbonate |
| CHEMIGUM |
CHEMIGUM™ P7D |
NBR-Dry |
Copolymer of butadiene-acrylonitrile partitioned with calcium carbonate |
| CHEMIGUM |
CHEMIGUM™ P83 |
NBR-Dry |
Copolymer of butadiene-acrylonitrile partitioned with PVC |
| CHEMIGUM |
CHEMIGUM™ P86F |
NBR-Dry |
Copolymer of butadiene-acrylonitrile partitioned with calcium carbonate |
| CHEMIGUM |
CHEMIGUM™ P8B-A |
NBR-Dry |
Copolymer of butadiene-acrylonitrile partitioned with PVC |
| CHEMIGUM |
CHEMIGUM™ P8D |
NBR-Dry |
Copolymer of butadiene-acrylonitrile partitioned with calcium carbonate |
| EMULTEX |
EMULTEX™ 4030 |
VACO |
EMULTEX 4030 is an APEO free vinyl acetate acrylic polymer dispersion with a good pigment binding power. It is suitable for formulating premium or general purpose interior coatings for general walls, ceiling, cement fibre board or paneling. |
| EMULTEX |
EMULTEX™ 4040 |
VACO |
EMULTEX 4040 is an APEO free vinyl acetate acrylic polymer dispersion with a good pigment binding power. It is suitable for formulating premium or general purpose interior coatings for general walls, ceiling, cement fibre board or paneling. |
| EMULTEX |
EMULTEX™ 4300 |
VA |
EMULTEX 4300 is a compounded, polyvinyl alcohol stabilised, vinyl acetate dibutyl maleate copolymer dispersion. |
| EMULTEX |
EMULTEX™ 8200 |
VACO |
EMULTEX 8200 is a fine to medium particle sized colloid stabilised vinyl acetate Veova 10 polymer dispersion with good pigment binding power. Based on APEO free surfactants, EMULTEX 8200 confers excellent application and performance characteristics in a wide range of interior emulsion paints. It is specifically designed to give high sheen with a “soft feel” finish in premium interior sheen coatings, or textured coatings. |
| EMULTEX |
EMULTEX™ A 1602 |
VA |
Aqueous emulsion of homopolymer vinyl acetate; non plasticized. |
| EMULTEX |
EMULTEX™ AD 230 |
VACO |
Emultex AD 230 is a water-based dispersion of vinyl acetate acrylic copolymer.Emultex AD 230 is properly recommended for coatings in contact with food and non-edible cheese rinds |
| EMULTEX |
EMULTEX™ CT 100H |
VA |
CT 100H is a readied for use and filled Vinyl Acetate homopolymer stabilised with specialty polyvinyl alcohol. It has good surface roughness coverage and yet good initial adhesion on paper and wood substrate. |
| EMULTEX |
EMULTEX™ CT 201 |
VA |
EMULTEX CT 201 is a readied for use and filled Vinyl Acetate homopolymer stabilised with specialty polyvinyl alcohol. It has good surface roughness coverage and yet good initial adhesion on paper and wood substrate. |
| EMULTEX |
EMULTEX™ CT 302 |
VA |
CT 302 is a plasticized Vinyl Acetate polymer. It possesses excellent wet tack and good bonding to paper/veneer and board. CT 302 is designed specially for general paper/veneer lamination application. It can be diluted with water from 10% to 30%. CT 302 can be applied both manually and by machine. Recommended coating weight is about 150 to 250gsm. |
| EMULTEX |
EMULTEX™ CT 400H |
VA |
CT 400H is a readied for use and filled Vinyl Acetate homopolymer stabilised with specialty polyvinyl alcohol. It has good surface roughness coverage and yet good initial adhesion on paper and wood substrate. |
| EMULTEX |
EMULTEX™ CT 9212 |
VA |
CT 9212 is a readied for use compounded and filled Vinyl Acetate homopolymer stabilised with specialty polyvinyl alcohol. It has good surface roughness coverage and yet good initial adhesion on paper and wood substrate. |
| EMULTEX |
EMULTEX™ FR 728 |
VACO |
EMULTEX FR 728 is a specially colloid stabilised vinyl acetate - vinyl versatate copolymer dispersion developed for formulation of water-borne intumescent
coatings. EMULTEX FR 728 provides a quick char formation with high expansion factor.EMULTEX FR 728 is designed for intumescent coatings for fire
protection up to R60. |
| EMULTEX |
EMULTEX™ FR 797 |
VACO |
EMULTEX FR 797 is a specially colloid stabilised and vinyl acetate - vinyl
versatate copolymer dispersion developed for formulation of waterborne intumescent coatings. EMULTEX FR 797 provides a slow char
formation with medium expansion factorEMULTEX FR 797 is recommended for intumescent coatings with fire protection up to 120min. |
| EMULTEX |
EMULTEX™ KR37 |
VA |
EMULTEX KR37 is a vinyl acetate homopolymer stabilised with polyvinyl alcohol and surfactants. It has a good wet tack and can be used as supplied or compounded depending on the adhesive applications. |
| EMULTEX |
EMULTEX™ KR37LV |
VA |
Emultex KR37LV is a vinyl acetate homopolymer stabilised with polyvinyl alcohol and surfactants. It has a good wet tack and can be used as supplied or compounded depending on the adhesive applications. |
| EMULTEX |
EMULTEX™ P 6320 |
VACO |
Emultex P 6320 is a water-based copolymer dispersion based on vinyl acetate and maleic acid dibutyl ester, recommended for manufacturing non-edible cheese crust.Emultex P 6320 is suitable for the manufacturing of physiologically perfect coatings for food, especially for the manufacturing of coatings for hard cheese.The specific national legislation must be taken into account. |
| EMULTEX |
EMULTEX™ P 7215 |
VACO |
Emultex P 7215 is a plasticizer-free water-based dispersion based on vinyl acetate and VeoVa (vinyl ester of versatic acid).Emultex P 7215 is especially suitable for the manufacturing of interior and exterior paints with excellent cost/performance relationship. It may also be used as a binder for the formulation of medium and medium-high PVC paints. Emultex P 7215 is also appropriate for the manufacturing of semi-gloss paints with good characteristics regarding gloss and blocking resistance. |
| EMULTEX |
EMULTEX™ P 7218 |
VACO |
Emultex P 7218 is a water-based dispersion based on vinyl acetate and VeoVa (vinyl ester of versatic acid). Emultex P 7218 is especially recommended for the formulation of interior and exterior paints on a wide PVC range.It is furthermore recommended for the manufacturing of semi-gloss paints and textured paints. |
| EMULTEX |
EMULTEX™ P 7252 |
VACO |
Emultex P 7252 is a plasticizer-free water-based dispersion based on vinyl acetate and VeoVa (vinyl ester of versatic acid).Emultex P 7252 is especially suitable for the manufacturing of interior and exterior paints with excellent water, saponification and weathering resistance. It is also appropriate for the manufacturing of semi-gloss paints. |
| EMULTEX |
EMULTEX™ P 7580 |
VACO |
Emultex P 7580 is a plasticizer-free water-based dispersion based on vinyl acetate and acrylic acid ester.Emultex P 7580 is especially recommended for the formulation of interior and exterior flat paints with medium and medium-high PVC. It is also recommended to formulate Semi-gloss paints.Emultex P 7580 is also suitable to produce Textured paints. |
| EMULTEX |
EMULTEX™ VV 579 |
VACO |
A vinyl acetate – versatate copolymer dispersion with fine
particle size, good water and alkali resistance. It is highly suitable for
broad wall decorative applications It posses good binding power, good scrub
resistance and suitable as a versatile binder for interior and exterior
applications
Emultex VV 579 is recommended for Interior matt, semi and
gloss finishes. It is also suitable for stucco and textured finishes |
| EMULTEX |
EMULTEX™ VV 665 |
VACO |
EMULTEX VV 665 is a medium particle size, specially colloid stabilised vinyl acetate - vinyl
versatate copolymer dispersion. EMULTEX VV 665 offers high scrub resistance, high gloss and good saponification resistance.EMULTEX VV 665 is recommended for solvent free matt and silk paints. When suitably compounded EMULTEX VV 665 is recommended as a binder in the production of flexible fillers, caulks and DIY cartridge applied sealants. |
| EMULTEX |
EMULTEX™ VV 675 |
VACO |
EMULTEX VV 675 is a medium particle size, colloid stabilised vinyl acetate - vinyl
versatate copolymer dispersion. EMULTEX VV 675 offers high scrub resistance and high exterior durability. EMULTEX VV 675 is recommended for exterior masonry paints and silk to gloss interior wall paints. |
| EMULTEX |
EMULTEX™ VV 676 |
VACO |
EMULTEX VV 676 is a medium particle size, colloid stabilized aqueous dispersion of a vinyl acetate - vinyl versatate - acrylate copolymer. EMULTEX VV 676 offers high scrub resistance, high exterior durabillity and good low temperature film forming properties. EMULTEX VV 676 is recommended for a broad range of interior and exterior masonry coatings. |
| EMULTEX |
EMULTEX™ VV 679 |
VACO |
EMULTEX VV 679 is a medium particle size, colloid stabilised vinyl acetate - vinyl versatate copolymer dispersion. EMULTEX VV 679 offers high scrub resistance and high gloss. EMULTEX VV 679 is recommended for matt and silk wall paints and also can be used in ready mixed fillers
and ceramic tile adhesives.
|
| ETHYL |
ETHYL ACRYLATE BIO BASED STABILIZED |
ACR |
Acrylic ester used for polymer manufacturing and as a raw material for syntheses. Molar Mass(g/mol): 100.12 Chemical formula: Stoichiometric formula: C5H8O2 CAS number: 140-88-5 |
| ETHYL |
ETHYL ACRYLATE STABILIZED |
ACR |
Acrylic ester used for polymer manufacturing and as a raw material for
syntheses.
Molar Mass(g/mol): 100.12
Chemical formula:
Stoichiometric formula: C5H8O2 CAS number: 140-88-5 |
| GENFLO |
GENFLO™ 3000 |
XSBR |
Polymer binder that provides a good balance of soft feel and tensile strength |
| GENFLO |
GENFLO™ 3060 |
XSBR |
Carboxylated styrene butadiene latex for nonwoven applications |
| GENFLO |
GENFLO™ 576 |
XSBR |
GenFlo 576Carboxylated styrene butadiene latex. General purpose polymer binder for paper, paperboard, and nonwovens applications. |
| GENFLO |
GENFLO™ 8045 |
XSBR |
GenFlo 8045 is a hydrophobic binder for carpet backing and nonwoven |
| GENGLAZE |
GENGLAZE® EC-2447 |
OTH |
Heat-activated in-mold coating designed to enhance the surface of molded parts.GenGlaze EC-2447 in-mold coating surface finish is incorporated during compression molding instead of being applied separately. It is environmentally friendly as it does not contain solvents (100% solids), and reduces the number of surface finishing steps and manufacturing costs. |
| PVAC |
H301 |
PVAC |
H301 is a medium / low molecular weight, solid polyvinyl acetate, developed for use as a thermoplastic low profile additive in unsaturated polyester composites. H301 is a carboxylated polymer which achieves low solution viscosity, efficient compound thickening, very low shrinkage and excellent mould release.
FEATURES
Rapidly dissolves in most organic solvents including styreneHigh thickening efficiencyExcellent solution stability and compatibilityNo shrinkageHigh gloss
H301 is manufactured on a dedicated polymerisation plant and is produced in the form of colourless beads. |
| HYDRO |
Hydro PLIOLITE® 010 |
SA |
Water-based acrylic modified resin based on proprietary Emulsifed Binding System (EBS) that provides outstanding adhesion to porous substrate and excellent film formation even in difficult conditions (low temperatrure and high humidity) that ensures excellent durability.Hydro Pliolite 010 is recommended for flat exterior masonry coatings, pigmented primers or interior tension-free paints. |
| HYDRO |
HYDRO PLIOLITE™ 050 |
PA |
Acrylate copolymer based on our ABS (Amphoteric Binding System) technology, contains anionic and cationic groups. Blocks many stains, including tannin, marker, and water stains.Hydro PLIOLITE 050 water-based resin was designed for low VOC stain blocking primers. |
| HYDRO |
Hydro PLIOLITE® 060 |
SA |
Water-based acrylic modified resin based on proprietary Emulsifed Binding System (EBS) that provides outstanding adhesion to porous substrate, strong consolidation effect thanks to its excellent penetration, and good resistance to efflorescence. Hydro Pliolite 060 is recommended for pigmented and transparent primers formulations |
| HYDRO |
HYDRO PLIOLITE™ 125 |
XSBR |
Hydro Pliolite 125 is a modified styrene butadiene copolymer with excellent odor blocking properties. Hydro Pliolite 125 was designed for the formulation of primers and coatings with odor blocking properties, especially those used in fire restoration projects. |
| HYDRO |
HYDRO PLIOLITE™ 211 |
SA |
Hydro Pliolite 211 is a modified styrene-acrylic copolymer dispersion developed for formulation of water-borne intumescent coatings. Hydro Pliolite 211 has excellent water resitance that allows intumescent coatings to resist to outdoor conditions.Hydro Pliolite 211 is designed for intumescent coatings for fire protection from R30 to R120. |
| HYDRO |
HYDRO PLIOLITE™ 330 |
PA |
Hydro Pliolite 330 is a multiphase pure acrylic copolymer dispersion designed for application on wood . Hydro Pliolite 330 provides an excellent adhesion and enhanced film formation in adverse climatic conditions that allows formulation of weather- and surface-tolerant wood coatings. Hydro Pliolite 330 is suitable for formulation of wood stains and wood trim paints. |
| HYDRO |
Pliotec XA 2547 |
PA |
Pliotec XA 2547 is a multiphase pure acrylic copolymer dispersion designed for exterior coatings, particularly on masonry. It provides enhanced film formation in adverse climatic conditions that makes it suitable for formulation of exterior coatings with early rain resistance, especially for tropical climates. |
| LIPATON |
LIPATON™ GF 3088 |
XSBR |
LIPATON GF 3088 is a latex for use as the primer or tack coating in the construction of rubberized running track and sports surfaces. |
| LIPATON |
LIPATON™ GF 3966 |
XSBR |
LIPATON GF 3966 is an adhesive binder used in the construction of rubberized running tracks and sports surfaces. |
| LIPATON |
LIPATON™ L 8262 |
XSBR |
LIPATON L 8262 is an aqueous styrene butadiene copolymer dispersion that is APEO free. This dispersion gives plasticising properties in cementitious systems. It also improves adhesion on various substrates. |
| LIPATON |
LIPATON™ SB 20W20 |
XSBR |
LIPATON SB 20W20 is an anionic carboxylated styrene/butadiene copolymer latex. |
| LIPATON |
LIPATON™ SB 2540 |
HSSBR |
LIPATON SB 2540 is an aqueous high solids dispersion of a styrene-butadiene copolymer. The dispersion is free from solvents and plasticizers and does not contain antioxidant. |
| LIPATON |
LIPATON™ SB 29Y141 |
XSBR |
LIPATON SB 29Y141 is a water-based non-ionically stabilized hydrolysis-resistant dispersion of a carboxylated styrene-butadiene copolymer. It contains an antioxidant and an antifoam and is compatible with most hydraulic binders. LIPATON SB 29Y141 has been designed particularly for applications like industrial flooring screeds. This product is free from APEOs and ammonia. |
| LIPATON |
LIPATON™ SB 29Y146 |
XSBR |
LIPATON SB 29Y146 is a water-based non-ionically stabilized hydrolysis-resistant dispersion of a carboxylated styrene-butadiene copolymer. The dispersion is freeze-thaw stable. It contains an antioxidant and an antifoam and is compatible with most hydraulic binders.This product is free from APEOs and ammonia. |
| LIPATON |
LIPATON™ SB 29Y57 |
XSBR |
LIPATON SB 29Y57 is a water-based non-ionically stabilised hydrolysis-resistant dispersion of a carboxylated styrene-butadiene copolymer contains an antioxidant, a defoamer and is free from APEOs. This product is compatible with most hydraulic binders. |
| LIPATON |
LIPATON™ SB 29Y57 PRC |
XSBR |
LIPATON SB 29Y57 PRC is a water-based non-ionically stabilised hydrolysis-resistant dispersion of a carboxylated styrene-butadiene copolymer contains an antioxidant, a defoamer and is free from APEOs. This product is compatible with most hydraulic binders. |
| LIPATON |
LIPATON™ SB 30Y160 |
XSBR |
LIPATON SB 30Y160 is a non-ionically stabilized, hydrolysis-resistant carboxylated styrenebutadiene copolymer latex. The dispersion contains an antioxidant and an antifoam agent, which is very effective for its use in hydraulic binders. This product is free from APEOs and ammonia. |
| LIPATON |
LIPATON™ SB 33Y50 |
XSBR |
LIPATON SB 33Y50 is an aqueous non-ionically stabilized dispersion of a carboxylated butadiene-styrene copolymer latex which is resistant against saponification. The dispersion is freeze-thaw stable. |
| LIPATON |
LIPATON™ SB 47B40 |
XSBR |
LIPATON SB 47B40 is an anionic, carboxylated styrene-butadiene copolymer latex containing a non-staining antioxidant. |
| LIPATON |
LIPATON™ SB 5521 |
XSBR |
Finely dispersed aqueous dispersion of a carboxylated styrene-butadiene copolymer. The dispersion contains an anionic emulsifier system and is free from film forming aids, APEO, solvents and plasticizers.LIPATON SB 5521 is a hydrophobic and elastic polymer. It is highly recommended for anti-corrosive primers and underbody coatings. |
| LIPATON |
LIPATON™ SB 5843 |
XSBR |
LIPATON SB 5843 is a ready-for-use aqueous dispersion of a styrene-butadiene copolymer with high stability against electrolytes. It contains an APEO free anionic/nonionic emulsifier system and is free from film forming aids, solvents, plasticizers, and ammonia. LIPATON SB 5843 contains a special defoamer to reduce the air content in cement mortars. |
| LIPATON |
LIPATON™ SB 60B11 |
XSBR |
LIPATON SB 60B11 is an anionic, carboxylated styrene-butadiene copolymer latex containing a non-staining antioxidant. |
| LIPOLAN |
LIPOLAN™ F 2040F |
HSSBR |
LIPOLAN F 2040F is an aqueous dispersion of a styrene-butadiene copolymer with a high solids content.
The emulsifier used is an alkaline salt of fatty acids, which provides a good stability and foamability. LIPOLAN F 2040F does not contain any antioxidant. LIPOLAN F 2040F is mainly used to produce moulded foam. Foam made of LIPOLAN F 2040F exhibits a very soft indentation hardness with a very high resilience.
|
| LIPOLAN |
LIPOLAN™ F 2420F |
HSSBR |
LIPOLAN F 2420F is an aqueous dispersion of a reinforced styrene-butadiene copolymer with a high solids content. The emulsifier used is an alkaline salt of fatty acids, which provides a good stability and foamability.
Moulded foam based on LIPOLAN F 2420F exhibits a soft indentation hardness with good resilience.
|
| LIPOLAN |
LIPOLAN™ F 2530F |
HSSBR |
Moulded foam products based on LIPOLAN F 2530F exhibit under usual ambient conditions a low indentation hardness with a low resilience, achieving a unique visco-elastic effect. LIPOLAN F 2530F is an aqueous dispersion of a styrene-butadiene copolymer with a high solids content. It is stabilsed using an alkaline salt of fatty acids, which also provides a good foamability. LIPOLAN F 2530F does not contain any antioxidant. |
| LIPOLAN |
LIPOLAN™ F 2610F |
HSSBR |
LIPOLAN F 2610F is an aqueous dispersion of a reinforced styrene-butadiene copolymer with a high solids content. The emulsifier used is an alkaline salt of fatty acids, which provides a good stability and foamability.
Moulded foam based on LIPOLAN F 2610F exhibits a high indentation hardness with a good resilience.
|
| LIPOLAN |
LIPOLAN™ F 2810F |
HSSBR |
LIPOLAN F 2810F is an aqueous dispersion of a reinforced styrene-butadiene copolymer with a high solids content. The emulsifier used is an alkaline salt of fatty acids, which provides a good stability and foamability.
Moulded foam based on LIPOLAN F 2810F exhibits a very high indentation hardness with a good resilience.
|
| LIPOLAN |
LIPOLAN™ F 2820F |
HSSBR |
LIPOLAN F 2820F is an aqueous dispersion of a reinforced styrene-butadiene copolymer with a high solids content. The emulsifier used is an alkaline salt of fatty acids, which gives the product good stability and foamability.
Moulded foam based on LIPOLAN F 2820F exhibits a medium high indentation hardness with a good resilience. |
| LIPREN |
LIPREN™ B |
CR |
LIPREN B is an aqueous high solids dispersion of a polymer of 2-chlorobutadiene (1.3). The dispersion contains an anionic emulsifier system and is free from film forming aids, solvents and plasticizers. |
| LIPREN |
LIPREN™ MKB |
CR |
LIPREN MKB is an aqueous, colloidal dispersion of a polymer of 2-chlorobutadiene (1,3). Its vulcanizates have a slight to medium crystallization tendency. LIPREN MKB is mainly used as a binder for fibres of all types. |
| LIPREN |
LIPREN™ T |
CR |
LIPREN T is an aqueous, colloidal dispersion of a polymer of 2-chlorobutadiene (1,3). Its vulcanizates have a slight to medium crystallization tendency and undergo little discolouration when exposed to light. LIPREN T is mainly used in the production of dipped goods. |
| LIPREN |
LIPREN™ X1112 |
CR |
LIPREN X1112 is an aqueous, colloidal dispersion of polymerised 2-chlorobutadiene (1,3). Vulcanised LIPREN X1112 has very little tendency to crystallize. LIPREN X1112 is mainly used in the production of dipped goods, but also for the production of flame retardant foams. It is either foamed or used to impregnate PU foams. |
| LITEX |
LITEX™ ALKASHIELD 1543 |
XSBR |
LITEX ALKASHIELDTM 1543 is an aqueous, anionic dispersion of a carboxylated self-crosslinking butadiene styrene copolymer containing a non-staining antioxidant. |
| LITEX |
LITEX™ LB-420 |
XSBR |
LITEX LB-420 is a styrene/butadiene
copolymer latex for use as a binder in the anode of lithium-ion batteries. It offers excellent mechanical and electrochemical performance. |
| LITEX |
LITEX™ LB-422 |
XSBR |
LITEX LB-422 is a styrene/butadiene
copolymer latex used as a binder in the anode of lithium-ion batteries. It offers a good balance of properties and cold temperature processing. |
| LITEX |
LITEX™ N 7012N |
NBR |
Litex N 7012N is an aqueous, anionic dispersion of a carboxylated styrene butadiene acrylonitrile copolymer containing a non-staining antioxidant. |
| LITEX |
LITEX™ NX 1200 |
NBR |
LITEX NX 1200 is an aqueous, plasticizer-free and formaldehyde reduced dispersion of a butadiene-acrylonitrile copolymer that can be crosslinked by heat. LITEX NX 1200 contains an anionic-nonionic emulsifier system and is stabilized with an antioxidant. |
| LITEX |
LITEX™ QUICKSHIELD 1545 |
XSBR |
LITEX QuickShield 1545 is an aqueous emulsion of a formaldehyde free, self-crosslinking copolymer of butadiene and styrene. |
| LITEX |
LITEX™ S 10656 |
XSBR |
LITEX S 10656 is an aqueous, anionic dispersion, of a carboxylated self-crosslinking butadiene styrene methacrylate copolymer, containing a non-staining antioxidant. |
| LITEX |
LITEX™ S 10726 |
XSBR |
LITEX S 10726 is an aqueous, anionic dispersion of a carboxylated self-crosslinking butadiene styrene copolymer, containing a non-staining antioxidant. |
| LITEX |
LITEX™ S 7140 |
XSBR |
LITEX S 7140 is an aqueous, anionic dispersion of a carboxylated styrene butadiene copolymer containing a non-staining antioxidant. |
| LITEX |
LITEX™ S 79A10 |
XSBR |
Litex S 79A10 is a carboxylated styrene/butadiene copolymer latex. |
| LITEX |
LITEX™ S 9076 |
XSBR |
Litex S 9076 is an aqueous, anionic dispersion of a self-crosslinking butadiene styrene copolymer containing a non-staining antioxidant. |
| LITEX |
LITEX™ SBV 600 |
XSBR |
LITEX SBV 600 is an aqueous emulsion of a self-crosslinking copolymer of butadiene and styrene. |
| LITEX |
LITEX™ SX 3060 |
XSBR |
Carboxylated styrene butadiene latex for nonwoven applications |
| LITEX |
LITEX™ SX 576 |
XSBR |
LITEX SX 576Carboxylated styrene butadiene latex. General purpose polymer binder for paper, paperboard, and nonwovens applications. |
| LITEX |
LITEX™ SX 8045 |
XSBR |
LITEX SX 8045 is a hydrophobic binder for carpet backing and nonwoven |
| LITEX |
LITEX™ T 56R60 |
XSBR |
Litex® T 56R60 is an aqueous dispersion of a carboxylated styrene-butadiene copolymer. The dispersion was developed for secondary backing, particularly for the two coat process. When this technique is employed the handle of the carpet is mainly influenced by the choice of the dispersion for the precoat. Litex® T 56R60 also can be used for the one coat process.
When this technique is employed the dispersion gives the carpet a soft handle.
Litex® T 56R60 contains an antioxidant. |
| LITEX |
LITEX™ T 64W20 |
XSBR |
Litex® T 64W20 is an aqueous dispersion of a carboxylated styrene-butadiene copolymer.
The dispersion was specially designed for the impregnation of needlefelt and also for the finishing of woven carpets. Litex® T 64W20 give the finished article a soft handle. Litex® T 64W20 is totally compatible with Litex® T 68W20. The products can therefore be mixed in any ratio to achieve the desired handle.
Litex® T 64W20 contains an antioxidant. |
| LITEX |
LITEX™ T 68W20 |
XSBR |
Litex® T 68W20 is an aqueous dispersion of a carboxylated styrene-butadiene copolymer.
The dispersion was specially designed for the impregnation of needlefelt and also for the finishing of woven carpets. Litex® T 68W20 give the finished article a hard handle.
Litex® T 68W20 is totally compatible with Litex® T 64W20. The products can therefore be mixed in any ratio to achieve the desired handle.
Litex® T 68W20 contains an antioxidant. |
| LITEX |
LITEX™ T 71S21 |
XSBR |
Litex® T 71S21 is an aqueous dispersion of a carboxylated styrene-butadiene copolymer.
The dispersion was developed for compounds designed for the production of drainage points and also for rubber crumb backings. It can also be used for precoats. When Litex® T 71S21 is used for precoats, the dispersion gives the carpets a soft handle.
Litex® T 71S21 contains an antioxidant. |
| LITHENE |
LITHENE™ ULTRA AH |
LPBD |
Lithene ultra AH is a highly viscous, low molecular weight, liquid polybutadiene with a high content of 1,2 vinyl and cyclic vinyl microstructures. It is a low odour and low VOC product used as a binder in automotive adhesives, coagent for EPDM rubbers and in hard electrical encapsulation systems.
TYPICAL APPLICATIONS
Automotive semi structural adhesives
Hard electrical encapsulants
Coagent in EPDM rubber compounds
Lithene ultra AH is despatched from our UK production plant. |
| LITHENE |
LITHENE™ ULTRA AL |
LPBD |
Lithene ultra AL is a viscous low molecular weight, liquid polybutadiene with high content of 1,2 vinyl and cyclic vinyl microstructures. It has low odour and is used as a binder in automotive sealants and in UV cured flexographic printing plates.
TYPICAL APPLICATIONS
Automotive sound damping sealants
Automotive semi structural adhesives
Antifoaming coating additives
Plasticiser for flexographic printing plates
Lithene ultra AL is despatched from our UK production plant. |
| LITHENE |
LITHENE ULTRA AL-15MA |
LPBD |
Lithene ultra AL-15MA is a highly viscous, low molecular weight, liquid polybutadiene. It is produced from the low odour base Lithene ultra AL, adducted with 15 parts maleic anhydride. It is used as a highly efficient adhesion promoter in sulphur cured automotive sealants.
TYPICAL APPLICATIONS
Adhesion promoter in automotive sealants and semi structural adhesives
Rubber to metal adhesion promoter
Electrical encapsulants
Lithene ultra AL-15MA is despatched from our UK production plant. |
| LITHENE |
LITHENE™ ULTRA N4-5000 |
LPBD |
Lithene ultra N4-5000 is a medium viscosity, narrow molecular weight, liquid polybutadiene with a low content of 1,2 vinyl micro structure. It is extremely low in both odour and volatiles and it can be used as a component in PU mould release formulations or as a base for further chemical modification such as maleinisation.
TYPICAL APPLICATIONS
Polyurethane foam mould release additive
Dry sand binder
Base polymer for maleinisation
Lithene ultra N4-5000 is despatched from our UK production plant. |
| LITHENE |
LITHENE™ ULTRA N4-5000-10MA |
LPBD |
Lithene ultra N4-5000-10MA is a viscous, low molecular weight, liquid polybutadiene. The polymer is very low in odour and volatiles and is produced from a narrow molecular weight polybutadiene base, adducted with 10 parts maleic anhydride.
TYPICAL APPLICATIONS:
Soft, isocyanate free, electrical encapsulants
Rubber to metal bonding
Lithene ultra N4-5000-10MA is despatched from our UK production plant> |
| LITHENE |
LITHENE™ ULTRA N4-5000-15MA |
LPBD |
Lithene ultra N4-5000-15MA is a highly viscous, low molecular weight, liquid polybutadiene. It is very low in odour and volatiles and is based on a narrow molecular weight polybutadiene adducted with 15 parts maleic anhydride.
TYPICAL APPLICATIONS:
Soft, isocyanate free electrical encapsulants
Adhesion promoter in automotive sealants
Rubber to metal adhesion promoter
Impact modifier for polyester resins
Lithene ultra N4-5000-15MA is despatched from our UK production plant. |
| LITHENE |
LITHENE™ ULTRA N4-9000 |
LPBD |
Lithene ultra N4-9000 is a viscous, narrow molecular weight liquid polybutadiene with a low content of 1,2 vinyl micro structure. It is extremely low in both odour and volatiles and can be used as a polyurethane additive to improve abrasion resistance.
TYPICAL APPLICATIONS
Polyurethane additive for abrasion resistance
Automotive sound damping sealants & adhesives
Dry sand binder
Lithene ultra N4-9000 is despatched from our UK production plant. |
| LITHENE |
LITHENE™ ULTRA N4-B-10MA |
LPBD |
Lithene ultra N4-B-10MA is a viscous, low molecular weight, liquid polybutadiene. The polymer is very low in odour and volatiles and is produced from a broad molecular weight polybutadiene base, adducted with 10 parts maleic anhydride.
TYPICAL APPLICATIONS:
Adhesion promoter in automotive sealants
Soft, isocyanate free electrical encapsulants
Rubber to metal bonding
Formulation of slow release fragrance gels
Lithene ultra N4-B-10MA is despatched from our UK production plant. |
| LITHENE |
LITHENE™ ULTRA P4-150P |
LPBD |
Lithene ultra P4-150P is a highly viscous, low molecular weight, liquid polybutadiene with microstructure containing 1,2 vinyl groups. It is very low in both odour and volatiles and can be used in chlorinated rubber feedstocks or automotive sealants.
TYPICAL APPLICATIONS
Feedstock for chlorinated rubber
Automotive sound damping sealants & adhesives
Lithene ultra P4-150P is despatched from our UK production plant. |
| LITHENE |
LITHENE™ ULTRA P4-25P |
LPBD |
Lithene ultra P4-25P is a viscous, low molecular weight, liquid polybutadiene with a medium content of 1,2 vinyl microstructure. It is extremely low in both odour and volatiles and can be used as a reactive plasticiser in flexographic printing plates.
TYPICAL APPLICATIONS
Reactive plasticiser in flexographic printing plates
Mould release additive for polyurethane foams
Antifoaming coating additives
Lithene ultra P4-25P is despatched from our UK production plant. |
| LITHENE |
LITHENE™ ULTRA PH |
LPBD |
Lithene ultra PH is a viscous, low molecular weight, liquid polybutadiene with a high content of 1,2 vinyl microstructure. It has extremely low odour and volatiles and is used in EPDM rubbers as a coagent and formulation of hard electrical encapsulants.
TYPICAL APPLICATIONS
Coagent in EPDM rubber compounds
Hard electrical encapsulants
Antifoaming coating additive
Reactive plasticiser in UV cure flexographic printing plates
Lithene ultra PH is despatched from our UK production plant. |
| LITHENE |
LITHENE™ ULTRA PM4 |
LPBD |
Lithene ultra PM4 is a low viscosity, low molecular weight, liquid polybutadiene with a medium content of 1,2 vinyl microstructure. It is extremely low in both odour and volatiles and is used as the binder in automotive sound damping sealants, polyurethane mould release systems and solvent based coating additives.
TYPICAL APPLICATIONS
Automotive sound damping sealants
Antifoaming coating additives
Non volatile drying oil in alkyd coatings
Sand binder for paving and moulds
Lithene ultra PM4 is despatched from our UK production plant. |
| LITHENE |
LITHENE™ ULTRA PM4-7.5MA |
LPBD |
Lithene ultra PM4-7.5MA is a medium viscosity, low molecular weight, liquid polybutadiene. It is very low in odour and volatiles and is produced from Lithene ultra PM4, adducted with 7.5 parts maleic anhydride.
TYPICAL APPLICATIONS
Adhesion promoter in automotive sealants
Rubber to metal adhesion promoter
Soft, isocyanate free electrical encapsulants
Lithene ultra PM4-7.5MA is despatched from our UK production plant. |
| LITHENE |
LITHENEACTIV™ 1000 |
LPBD |
LitheneActiV 1000 is a liquid polybutadiene with very high content of 1,2 vinyl microstructure. It is a highly reactive polymer with low volatiles and odour. It is designed for use as a highly effective Type II coagent in peroxide or sulphur cured elastomers where it allows better mixing and enhanced physical cured thermoset properties.
TYPICAL APPLICATIONS
Automotive sulphur or peroxide cured sealants & adhesivesCoagent in sulphur or peroxide cured rubbers and elastomers
LitheneActiV 1000 is despatched from our UK production plant. |
| LITHENE |
LITHENEACTIV™ 50 |
LPBD |
LitheneActiV 50 is a liquid polybutadiene with very high content of 1,2 vinyl microstructure. It is a highly reactive polymer with low volatiles and odour. It is used as a reactive plasticiser in UV cured flexographic printing plates and as a reactive diluent in solvent based coating systems.
TYPICAL APPLICATIONS
Reactive plasticiser for flexographic printing plates
Automotive semi structural adhesives
Reactive diluent in solvent based coating systems
LitheneActiV 50 is despatched from our UK production plant. |
| LYTRON |
LYTRON™ 180 |
SA |
Mildly acidic brilliant white opacifier preserved with 2-bromo-2-nitropropane-1,3-diol.Lytron 180 opacifier for bath and shower products, including liquid hand wash and soaps, laundry detergents, and cleaners |
| LYTRON |
LYTRON™ 180 AV |
SA |
Acidic un-neutralized opacifier for home and personal care products with no added preservatives.Lytron 180 AV styrene acrylic copolymer opacifier for bath and shower products, including liquid hand wash and soaps, laundry detergents, and cleaners. |
| PVAC |
M30 |
PVAC |
M30 is a low molecular weight, solid polyvinyl acetate. It is designed for use in solvent based coatings, inks and adhesives or melt extrusion systems. M30 can also be used as a low profile additive in unsaturated polyester composites, typically pultrusion and BMC processes.
FEATURES
Rapidly dissolves in most organic solvents.
Can be melt processed.
Easily plasticised.
Can be combined with other M Grades.
Excellent substrate adhesion & film flexibility.
Very high light stability.
M30 is manufactured on a dedicated polymerisation plant and is produced in the form of colourless beads. |
| PVAC |
M35-73 SOLUTION |
PVAC |
M35/73 Solution is a copolymer of vinyl acetate and dibutyl maleate dissolved in ethyl acetate. It is designed for use mainly in solvent based coatings, where it can be diluted for use as a highly efficient primer and sealer.
FEATURES
Miscible with most organic solvents
Very high resistance to hydrolysis
Solution polymer
Rapid penetration and binding
Excellent low temperature heat seal
M35/73 Solution is manufactured on a dedicated polymerisation plant and is produced in the form of a colourless solution. |
| PVAC |
M40 |
PVAC |
M40 is a medium molecular weight, solid polyvinyl acetate. It is designed for use in solvent based coatings, inks and adhesives or melt extrusion systems. M40 can also be used as a low profile additive in unsaturated polyester composites, typically pultrusion and BMC processes.
FEATURES
Rapidly dissolves in most organic solvents including styrene
Can be melt processed
Easily plasticised
Can be combined with other M Grades
Excellent low profile performance in BMC & pultrusion processes
M40 is manufactured on a dedicated polymerisation plant and is produced in the form of colourless beads. |
| PVAC |
M50 |
PVAC |
M50 is a medium molecular weight, solid polyvinyl acetate. It is designed for use in solvent based general purpose or parquet adhesives, coatings and inks, melt extrusion systems such as automotive sound damping foils and as a B side carrier in polyester SMC manufacture.
FEATURES
Rapidly dissolves in most organic solvents.
Can be melt processed.
Easily plasticised.
Can be combined with other M Grades.
Excellent adhesion to a wide range of substrates.
Very high UV & light stability.
M50 is manufactured on a dedicated polymerisation plant and is produced in the form of colourless beads. |
| PVAC |
M60 |
PVAC |
M60 is a medium high molecular weight, solid polyvinyl acetate. It is designed for use in solvent based coatings, inks and adhesives or melt extrusion systems such as automotive sound damping foils.
FEATURES
Rapidly dissolves in most organic solvents.
Can be melt processed.
Easily plasticised.
Can be combined with other M Grades.
Excellent adhesion to a wide range of substrates.
Very high light and thermal stability.
M60 is manufactured on a dedicated polymerisation plant and is produced in the form of colourless beads. |
| PVAC |
MCT5 |
PVAC |
MCT5 is a low molecular weight, solid copolymer of vinyl acetate and crotonic acid. It is an extremely versatile polymer soluble in both solvent and alkaline aqueous systems.
FEATURES
Rapidly dissolves in most organic solvents
Dissolves in aqueous systems at pH >7.0
Can be melt processed and plasticised
Crosslinkable
Can be combined with other M Grades
Very high adhesion to metals and plastics
High light stability
MCT5 is manufactured on a dedicated polymerisation plant and is produced in the form of clear, slightly yellow granules. |
| METHYL |
METHYL ACRYLATE, STABILIZED |
ACR |
Acrylic ester used for polymer manufacturing and as a raw material for
syntheses.
Molar Mass(g/mol): 86.09
Chemical formula:
Stoichiometric formula: C4H6O2CAS number: 96-33-3 |
| MOR-GLO |
MOR-GLO™ 10 |
SA |
Floor finish, water-based styrene acrylic, polymer emulsion for ultra-high speed (UHS) maintenance programMor-Glo 10 provides a very repairable surface that has a high distinctness of image without compromising the abrasion, soil and shoe scuff resistance associated with high performance floor finishes. |
| MOR-GLO |
MOR-GLO™ 2 |
SA |
Floor finish, water-based styrene acrylic, polymer emulsion for high traffic applications, such as schools, hospitals and retail.Mor-Glo 2 very hard and durable zinc crosslinked polymer provides premium performance in high traffic floor areas. It features excellent black heel mark (BHMR), scuff and dirt resistance. |
| MOR-GLO |
MOR-GLO™ 2E |
SA |
Floor finish, water-based styrene acrylic, polymer emulsion for high traffic applications, such as schools, hospitals and retail.Mor-Glo 2E very hard and durable zinc crosslinked polymer provides premium performance in high traffic floor areas. It features excellent black heel mark (BHMR), scuff and dirt resistance. |
| MOR-GLO |
MOR-GLO™ 8 |
SA |
Floor finish, water-based styrene acrylic, polymer emulsion for high traffic applications, such as schools, hospitals and retail.Mor-Glo 8 zinc crosslinked floor finish polymer is used to make premium, well-balanced floor polishes that provide outstanding dirt resistance, reparability, and response to periodic ultra high speed maintenance. |
| MOR-GLO |
MOR-GLO™ 877 |
SA |
Floor finish, water-based styrene acrylic, polymer emulsion for industrial, residential and general purpose polishes with good wear resistance.Mor-Glo 877 general use polymer is frequently recommended for low maintenance floor finishes. It can be used as sole polymer or blended with others. |
| MOR-GLO |
MOR-GLO™ DURABLE |
SA |
Next generation water-based polymer for long lasting, high performance floor finishes in high traffic environmentsMOR-GLO™ DURABLE is a styrene acrylic polymer that delivers durability and extended protection, reducing labor costs and business down-time by decreasing the number of stripping and re-polishing cycles during the life of the floor. |
| MOR-GLO |
MOR-GLO™ G128 |
SA |
Zinc-free floor finish, water-based styrene acrylic, polymer emulsion for high traffic applications, such as schools, hospitals and retail.Mor-Glo G128 is recommended for low maintenance floor finishes. It can be easily formulated into EPA Safer Choice, Green Seal and Ecologo certifiable floor finishes. |
| MOR-GLO |
MOR-GLO™ ULTRA AR |
SA |
Alcohol resistant floor finish, water-based styrene acrylic, polymer emulsion for high traffic environments.Mor-Glo Ultra AR provides a very durable, high gloss surface that is resistant to alcohol based hand sanitizers but that still retains the reparability and removability of one-component floor finish. |
| MOR-GLO |
MOR-GLO™ ULTRA G |
SA |
Zinc-free Twin-LinkedTM, water-based styrene acrylic, polymer emulsion for low or high maintenance floor polish formulations.Mor-Glo Ultra G zinc-free polymer delivers the durability and performance of premium zinc-containing finishes. It is crosslinked using SYNTHOMER Solutions' Twin-LinkedTM technology to deliver premium durability and performance. |
| MOR-SHINE |
MOR-SHINE™ 4U |
OTH |
General purpose and cost effective floor polish concentrate.Mor-Shine 4U dry-bright polish concentrate with excellent gloss retention, as well as mar and scratch resistance, is used for general purpose finishes that respond to low and high maintenance schedules. |
| MOR-SHINE |
MOR-SHINE™ E |
OTH |
Mor-Shine E is a dry-bright polish concentrate with excellent gloss retention, as well as mar and scratch resistance.Mor-Shine E is used for general purpose finishes that respond to low and high maintenance schedules. |
| MOR-SHINE |
MOR-SHINE™ ULTRA CSG |
OTH |
A concentrated surface protectant for use on polished or decorative concrete surfacesMor-shine Ultra CSG penetrates into functional concrete surfaces and provides excellent durability and protection from stains and abrasion |
| MYKON |
MYKON™ HLC |
OTH |
Lubricant for nonwovens, textiles, and paper applications. |
| N-BUTYL |
N-BUTYL ACRYLATE, STABILIZED |
ACR |
Acrylic ester used for polymer manufacturing and as a raw
material for syntheses.
Molar Mass(g/mol): 128.17
Chemical formula:Stoichiometric formula:
C7H12O2CAS: 141-32-2
|
| NOVACRYL |
NOVACRYL™ 3797 |
PA |
Water-based, pressure sensitive acrylic designed for removable applications |
| NOVACRYL |
NOVACRYL™ PS-R 300 |
PA |
Water-based acrylic polymer designed for removable pressure sensitive adhesives for masking and painter's tapes, labels, and protective films |
| OMNAPEL |
OMNAPEL™ 3158 |
VACO |
Hydrophobic acrylate copolymer for the formulation of waterproof coatings and binders |
| PLEXTOL |
PLEXTOL™ A 6474 |
PA |
PLEXTOL A 6474 is an aqueous dispersion of an acrylic
copolymer with heterogeneous particle morphology.
PLEXTOL A 6474 is a binder for exterior and interior clear
or pigmented wood coatings. |
| PLEXTOL |
PLEXTOL™ B 500 |
PA |
Aqueous dispersion of a non-ionic stabilized thermoplastic acrylic polymer. The dispersion is free from film forming aids, APEO, solvents and plasticizers.PLEXTOL B 500 is a pure acrylic with an excellent shear and electrolyte stability. It is highly recommended for silicone paints and artist paints. It shows high flexibility and UV-resistance. |
| PLEXTOL |
PLEXTOL™ BV 380 |
PA |
PLEXTOL BV 380 is an aqueous emulsion of a self-crosslinking acrylic polymer. |
| PLEXTOL |
PLEXTOL™ BV 411 |
PA |
PLEXTOL BV 411 is an aqueous emulsion of a self-crosslinking acrylic polymer. |
| PLEXTOL |
PLEXTOL™ D 237 |
PA |
PLEXTOL D 237 is an aqueous emulsion of a thermoplastic acrylic polymer. |
| PLEXTOL |
PLEXTOL™ D 2610 |
PA |
PLEXTOL D 2610 is an aqueous dispersion of an acrylic
copolymer.
PLEXTOL D 2610 dispersion is designed for various types of
paints, on a wide range of pigment volume concentration (% PVC), from varnish
to matt paints.
|
| PLEXTOL |
PLEXTOL™ D 268 |
PA |
PLEXTOL D 268 an aqueous acrylic emulsion for PSA applications. |
| PLEXTOL |
PLEXTOL™ D 324 |
PA |
PLEXTOL D 324 is an aqueous, high solids dispersion of an acrylic ester copolymer. The dispersion contains an anionic/nonionic emulsifier system and is free from film forming aids, solvents and plasticizers. |
| PLEXTOL |
PLEXTOL™ D 335 |
PA |
PLEXTOL D 335 is a high solids aqueous dispersion of a modified acrylic copolymer. The dispersion contains an anionic, APEO free emulsifier system and is free from film forming aids, solvents and plasticizers. |
| PLEXTOL |
PLEXTOL™ D 471 NA |
PA |
PLEXTOL D 471 NA is an acrylic binder used as the top coat on rubberized running tracks and sports surfaces.PLEXTOL D 471 NA can also be used in the modification of cement and concrete admixtures. |
| PLEXTOL |
PLEXTOL™ D 487 |
PA |
Finely dispersed aqueous dispersion of a methacrylic ester-acrylic ester copolymer. The dispersion contains an anionic emulsifier system and is free from film forming aids, solvents, and plasticizers.PLEXTOL D 487 is a low MFFT self-crosslinking pure acrylic with excellent adhesion on different substrates. It is highly recommended as multi-substrate binder and for universal renovation paints ("house-paints"). |
| PLEXTOL |
PLEXTOL™ D 498 |
PA |
Finely dispersed aqueous dispersion of a methacrylic ester-acrylic ester copolymer. The dispersion contains an anionic emulsifier system and is free from film forming aids, solvents and plasticizers.PLEXTOL D 498 is a low MFFT pure acrylic recommended for saponification resistant exterior masonry coatings and renders. It is highly suitable for silicate coatings and renders and shows non-yellowing and excellent UV resistance. |
| PLEXTOL |
PLEXTOL™ D 509 |
PA |
PLEXTOL D 509 is a ready-for-use finely dispersed aqueous dispersion of a methacrylic ester-acrylic ester copolymer. The dispersion contains an anionic/nonionic emulsifier system and is free from film forming aids, solvents and plasticizers. |
| PLEXTOL |
PLEXTOL™ D 5241 |
PA |
PLEXTOL D 5241 is an aqueous, high solids dispersion of an acrylic ester copolymer. The dispersion contains an APEO free anionic/nonionic emulsifier system and is free from film forming aids, solvents and plasticizers. |
| PLEXTOL |
PLEXTOL™ D 904 |
PA |
Plextol D 904 is a water-based dispersion based on acrylic and methacrylic acid esters.Plextol D 904 is mostly advised to formulate Facade coatings with very good water and UV resistance. It can also be used to formulate Interior paints and Primers for walls. |
| PLEXTOL |
PLEXTOL™ D 977 |
PA |
Plextol D 977 is a water-based dispersion of acrylic copolymer designed for Elastomeric coatings, roof and walls.It provides a good balance between mechanical properties and dirt pick-up resistance thanks to the adjusted internal plastification and UV surface curing system. |
| PLEXTOL |
PLEXTOL™ DV 245 |
PA |
PLEXTOL DV 245 is an aqueous emulsion of a self-crosslinking acrylic polymer. |
| PLEXTOL |
PLEXTOL™ DV 455 |
PA |
PLEXTOL DV 455 is an aqueous emulsion of a self-crosslinking acrylic polymer. |
| PLEXTOL |
PLEXTOL™ DV 544 |
PA |
PLEXTOL DV 544 is an aqueous emulsion of a crosslinkable acrylic polymer. |
| PLEXTOL |
PLEXTOL™ DV 585 |
PA |
PLEXTOL DV 585 is an aqueous emulsion of a self-crosslinking acrylic polymer. |
| PLEXTOL |
PLEXTOL™ E 303 |
PA |
PLEXTOL E 303 is an aqueous high solids dispersion of an acrylic ester copolymer. The dispersion contains an anionic emulsifier system and is free from film forming aids, solvents and plasticizers. |
| PLEXTOL |
PLEXTOL™ L 4801 |
PA |
PLEXTOL L 4801 is an aqueous dispersion of acrylic copolymer for specialty pressure sensitive tapes. It is anionic and APEO free. |
| PLEXTOL |
PLEXTOL™ L 4804 |
PA |
Aqueous dispersion of acrylic copolymer, anionic, APEO free. |
| PLEXTOL |
PLEXTOL™ L 4805 |
PA |
Aqueous dispersion of acrylic copolymer, anionic, APEO free. |
| PLEXTOL |
PLEXTOL™ M 625 |
PA |
Finely dispersed aqueous dispersion of a methacrylic ester-acrylic ester copolymer. The dispersion contains an anionic emulsifier system, and is free from APEO, coalescing agents, solvents, and plasticizers.PLEXTOL M 625 is a hard pure acrylic with excellent UV-resistance and exterior durability. It is highly recommended for industrial concrete roof-tile and fibre-cement coatings. It shows an outstanding efflorescence and water-whitening resistance. |
| PLEXTOL |
PLEXTOL™ M 630 |
PA |
PLEXTOL M 630 is an aqueous emulsion of a thermoplastic acrylic polymer. |
| PLEXTOL |
PLEXTOL™ P 7730 |
PA |
Plextol P 7730 is a water-based dispersion acrylic copolymer modified, internally crosslinked and UV-cured.It is specially designed for Elastomeric wall and roof coatings that provides excellent aging behavior and exhibits low water uptake, alkali resistance and high elongation even at very low temperatures. |
| PLEXTOL |
PLEXTOL™ P 7744 |
PA |
Plextol P 7744 is a plasticizer-free water-based dispersion based on acrylic and methacrylic acid esters.Plextol P 7744 is suitable for the manufacturing of high quality exterior paints with excellent weathering resistance and low dirt pick-up. |
| PLEXTOL |
PLEXTOL™ P 7776 |
PA |
Plextol P 7776 is a water-based acrylic dispersion for Exterior facade paints as well as for Semi-gloss to High-gloss wall paints.Plextol P 7776 provides good exterior durability (color retention for deep-shade paints) and snail trail resistance. |
| PLEXTOL |
PLEXTOL™ P 7778 |
PA |
Plextol P 7778 is a plasticizer-free water-based dispersion based on acrylic and methacrylic acid esters.Plextol P 7778 is specially recommended for the formulation of High gloss paints on several types of substrates providing high wet adhesion, outdoor durability and low dirt pick-up.It can be also used for Wood stain, Facade coatings and Semi-gloss paints. |
| PLEXTOL |
PLEXTOL P™ 7788 |
PA |
Plextol P 7788 is a plasticizer-free water-based dispersion based on acrylic and methacrylic acid esters.Plextol P 7788 is recommended for Facade and Wall paints with low VOC emissions. It provides good binding power and exterior durability. |
| PLEXTOL |
PLEXTOL™ PRIME 7520 |
PA |
Plextol Prime 7520 is a coater ready acrylic emulsion polymer for applications where good
low surface energy bonding is needed. |
| PLEXTOL |
PLEXTOL™ R 100 |
PA |
Plextol R 100 is a surfactant stabilised modified - acrylic copolymer dispersion that forms a flexible, tough film of high water resistance.Plextol R 100 is recommended for exterior and interior
paints. |
| PLEXTOL |
PLEXTOL™ R 123 |
PA |
PLEXTOL R 123 is an acrylic copolymer dispersion. |
| PLEXTOL |
PLEXTOL™ R 123 |
PA |
Plextol R 123 is an acrylic copolymer dispersion |
| PLEXTOL |
PLEXTOL™ R 272 |
PA |
Plextol R 272 is a fine particle size, surfactant stabilised, self-crosslinking acrylic copolymer dispersion. |
| PLEXTOL |
PLEXTOL™ R 4138 |
PA |
PLEXTOL R 4138 is a fine particle sized acrylic
polymer dispersion designed for use in a wide range
of paint formulations. It has outstanding
performance especially in premium highly durable
exterior paints. |
| PLEXTOL |
PLEXTOL™ R 4164 |
PA |
PLEXTOL R 4164 is acrylic polymer dispersion
stabilized by a unique non APEO surfactants system. It exhibits a high
blanching resistance to water which makes it perfectly suitable for formulating non whitening clearcoat for floor, stone finishes, wooden surfaces and roof tiles. Due to its fine particle size, it is best suited for penetrating primer sealer over chalky surfaces which needs reinforcement. Excellent for interior or exterior colored opaque finishes too.
|
| PLEXTOL |
PLEXTOL™ R 4184 |
PA |
PLEXTOL R 4184 is an acrylic polymer dispersion based on
APEO free surfactants and designed for use in premium highly
durable exterior paint. It does not contain any added
formaldehyde. This specially designed acrylic is also suitable for roof coatings. |
| PLEXTOL |
PLEXTOL™ R 4189 |
PA |
PLEXTOL R 4189 is a fine particle sized acrylic polymer dispersion stabilised by APEO free surfactants. It is recommended for wood coating application. |
| PLEXTOL |
PLEXTOL™ R 5335 |
PA |
PLEXTOL R 5335 is a fine particle size, surfactant stabilised aqueous acrylic copolymer dispersion. PLEXTOL R 5335 offers high gloss, excellent adhesion and high water resistance. PLEXTOL R 5335 is recommended for high performance trim paints and wood stains. |
| PLEXTOL |
PLEXTOL™ R 5441 |
PA |
PLEXTOL R 5441 is a fine particle size, surfactant stabilised aqueous dispersion of a crosslinked methacrylic ester-acrylic
ester copolymer. PLEXTOL R 5441 offers high gloss, block resistance, wet ahdesion, alkali and water resitance. PLEXTOL R 5441 is recommended for low-to-medium build wood stains and semigloss to silky matt wet room coatings. |
| PLEXTOL |
PLEXTOL™ R 5512 |
PA |
Plextol R 5512 is a water-based pure acrylic copolymer dispersion mainly recommended for Crack bridging wall paints and highly flexible roof coatings.Plextol R 5512 provides high flexibility and expceptional water, alkali and dirt pick-up resistance.It contributes a good balance between mechanical properties and dirt pick-up resistance thanks to the adjusted internal plastification and UV surface curing system. |
| PLEXTOL |
PLEXTOL™ R 5530 |
PA |
PLEXTOL R 5530 is a fine particle size, surfactant stabilised
aqueous dispersion of a crosslinked methacrylic ester-acrylic ester
copolymer. PLEXTOL R 5530 offers good adhesion and salt spray resistance with a very good adhesion to different substrates.PLEXTOL R 5530 is recommended for anti-corrosion and Direct to Meta applications with excellent salt spray resistance and perfect adhesion to many substrates. Plextol R 5530 is suitable also for multi-substrate primer formulations. |
| PLEXTOL |
PLEXTOL™ R 621 |
PA |
PLEXTOL R 621 is an aqueous dispersion of an acrylic ester copolymer with pressure sensitive properties. |
| PLEXTOL |
PLEXTOL™ R 815 |
PA |
PLEXTOL R 815 is a fine particle size, surfactant stabilised
aqueous dispersion of a methacrylic ester-acrylic ester copolymer. PLEXTOL R 815 offers high gloss, block resistance, wet adhesion, alkali and water resistance. PLEXTOL R 815 is recommended for gloss paints, varnishes and stains. |
| PLEXTOL |
PLEXTOL™ R 825 D |
PA |
PLEXTOL R 825 D is a finely dispersed aqueous acrylic copolymer dispersion. The dispersion contains an anionic emulsifier system and is free from APEO, film forming aids, solvents and plasticizers.PLEXTOL R 825 D is a self-crosslinking multiphase acrylic dispersion. It is highly recommended for gloss and trimpaints. It offers high gloss potential, excellent wet adhesion and good blocking resistance. |
| PLEXTOL |
PLEXTOL™ R 825 N |
PA |
Plextol R 825 N is a finely dispersed aqueous acrylic copolymer dispersion. The
dispersion contains an anionic emulsifier system and is free from
APEO, film forming aids, solvents and plasticizers.
PLEXTOL R 825 N is a self-crosslinking multiphase acrylic
dispersion. It is highly recommended for gloss and trimpaints. It
offers high gloss potential, excellent wet adhesion and good
blocking resistance. |
| PLEXTOL |
PLEXTOL™ R 8868 |
PA |
Pure Acrylic copolymer dispersion with fine particle size and excellent UV and water resistance. The product has very good weathering resistance, low dirt pick up and can be used to formulate premium quality coatings for interior and exterior applications.Plextol 8868 is recommended for high quality architectural coatings suitable for matt to semi gloss formulations, solar reflective coatings. |
| PLEXTOL |
PLEXTOL™ RM 1017 |
SA |
PLEXTOL RM 1017 is a surfactant stabilised modified - acrylic copolymer dispersion. The dispersion is free from film forming aids, APEO, solvents and plasticizers.PLEXTOL RM 1017 forms a flexible, tough film of high water resistance. It is recommended for roadmarking paints. |
| PLEXTOL |
PLEXTOL™ UF PR 3500K |
PA |
PLEXTOL UF PR 3500K is an aqueous dispersion of acrylic copolymer with an ultrafine particle size designed in use of primers for porous masonry and timber substrates. Due to its low film forming temperature and adherent films, primed surfaces are smooth and “keyed in” for the final decorative coating. |
| PLEXTOL |
PLEXTOL™ UG 3852 |
PA |
PLEXTOL UG 3852 is an ammonia-free aqueous
dispersion of an acrylic copolymer.
PLEXTOL UG 3852 is designed for formulating
environmentally friendly low odour interior and exterior masonry coatings
(façade coatings and synthetic resin plasters). |
| PLEXTOL |
PLEXTOL™ ULTRAFINE LS 5000 |
PA |
PLEXTOL ULTRAFINE LS 5000 is an ultra fine particle size, surfactant stabilised
aqueous dispersion of a methacrylic ester-acrylic ester and vinyl versatate copolymer with translucent appearance. PLEXTOL ULTRAFINE LS 5000 shows excellent penetration and binding properties especially for surfaces which may be subjected to significant dimensional changes. PLEXTOL ULTRAFINE LS 5000 is recommended for wood stains formulation for interior and exterior application. |
| PLEXTOL |
PLEXTOL™ ULTRAFINE PR 3500 |
PA |
PLEXTOL UltraFine PR 3500 is an aqueous dispersion of acrylic copolymer with a very fine particle size. |
| PLEXTOL |
PLEXTOL™ ULTRAFINE PR 3500 |
PA |
PLEXTOL UltraFine PR 3500 is an aqueous dispersion of acrylic copolymer with a very fine particle size. |
| PLEXTOL |
PLEXTOL™ W 1078 |
PA |
PLEXTOL W 1078 is a multiphase, self-crosslinking acrylic copolymer dispersion designed for interior use for varnish and stain formulations of parquet and furniture. |
| PLEXTOL |
PLEXTOL™ X 4427 |
PA |
PLEXTOL X 4427 is an aqueous emulsion of an acrylic-copolymer. |
| PLEXTOL |
PLEXTOL™ XA 2624 |
PA |
Aqueous dispersion of acrylic copolymer, anionic, APEO free. |
| PLIOCORD |
PLIOCORD™ SB 2108 |
LSSBR |
Cold-polymerized non-carboxylated SB latex for fiber-to-rubber adhesion for tires and rubber products |
| PLIOCORD |
PLIOCORD™ VP 106 |
VPSBR |
Industry standard latex for fiber-to-rubber adhesion for tires and rubber products. |
| PLIOCORD |
PLIOCORD™ VP 106S |
VPSBR |
Latex for fiber-to-rubber adhesion for tires and rubber products with low-foaming characteristics |
| PLIOCORD |
PLIOCORD™ VP 107S |
VPSBR |
Latex with lower VP level for fiber-to-rubber adhesion for tires and rubber products |
| PLIOCORD |
PLIOCORD™ VP 108S |
VPSBR |
Latex with lower VP level for fiber-to-rubber adhesion for tires and rubber products |
| PLIOCORD |
PLIOCORD™ VP 109 |
VPSBR |
Latex for textile-to-rubber adhesion for tires and rubber products |
| PLIOCORD |
PLIOCORD™ VP 4668 |
VPSBR |
Latex for fiber-to-rubber adhesion with superior runnability for demanding formulas |
| PLIOCRYL |
PLIOCRYL™ 4526 |
OTH |
Pliocryl 4526 is an orthophthalic unsaturated polyester solvent-based resin.Mainly recommended for two-component traffic marking paints, especially pedestrian crossings, parking lots, streets, auxiliary markings.Pliocryl 4526 provides a good balance of flexibility and hardness after curing, as well as weather and abrasion resistances.Pliocryl 4526 can be cured at room T by means of the addition of one initiator (e.g. benzoyl peroxide - BP.As plasticizer agent it's recommended the use of paraffine choride solvents with high temperature resistance. |
| PLIOCRYL |
PLIOCRYL™ 4528 |
OTH |
Pliocryl 4528 is an orthophthalic unsaturated polyester solvent-based resin, pre-accelerated, with extended curing time and diluted in acrylic solvents.Mainly recommended for two-component traffic marking paints, especially pedestrian crossings, parking lots, streets, auxiliary markings.Pliocryl 4528 provides a good balance of flexibility and hardness after curing, as well as weather and abrasion resistances. |
| PLIOCRYL |
PLIOCRYL™ 4600 |
ACR |
Pliocryl 4600 is a thermoplastic solvent-based styrene-acrylic copolymer.It provides extremely fast drying, high hardness and good water resistance properties.Mainly recommended for traffic marking and floor paints. |
| PLIOCRYL |
PLIOCRYL™ 4660 |
ACR |
Pliocryl 4660 is a thermoplastic solvent-based styrene-acrylic copolymer.It provides fast drying, good mechanical properties and good water resistance.Mainly recommended for swimming pools paints as well as floor and traffic marking paints. |
| PLIOLAK |
PLIOLAK™ AF 475 |
ALK |
Pliolak AF 475 is a Solvent-based medium-oil alkyd resin based on vegetable fatty acids.Pliolak AF 475 is mainly suitable for the manufacturing of fast-drying industrial enamels. Pliolak AF 475 65 % in Xylene is suitable for the manufacturing of enamels finished with xylene.It may also be used in forced-drying enamels (between 60 ºC and 100 ºC) as sole binder or in combination with melamine resins.The resin contains 47% oil and 27% phthalic anhydrid.Delivery form : (1) 55% in White Spirit/Xylene or (2) 65% in Xylene |
| PLIOLAK |
PLIOLAK™ AF 522 |
ALK |
Pliolak AF 522 is a Solvent-based medium-oil alkyd resin for decorative coatings, industrial primers and enamelsThe resin contains 52% oil and 28% phthalic anhydrid.Delivery form 60% in D40 |
| PLIOLAK |
PLIOLAK™ AF 642 |
ALK |
Pliolak AF 642 is a Sovent-based long-oil drying alkyd resin based on vegetable fatty acids.Pliolak AF 642 is used as sole binder or in combination with other alkyd resins for the formulation of decorative enamels and varnishes.Pliolak AF 642 is also suitable for the production of metal and wood primers and anti-corrosion paints.The 100% resin contains 64% oil and 24 % Phthalic Anhydride Delivery form 60 % in Dearomatized White Spirit |
| PLIOLAK |
PLIOLAK™ AF 654 E |
ALK |
Pliolak AF 654E is a Solvent-based long-oil drying alkyd resin based on vegetable fatty acids.Pliolak AF 654E is recommended as sole binder or in combination with other alkyd resins for the formulation of decorative enamels and varnishes.It can also be used for the production of primers and anti-corrosion paints.The resin contains 65% Oil and 26% Phthalic Anhydride Delivery form 70 % in White Spirit |
| PLIOLAK |
PLIOLAK™ AF 704 |
ALK |
Pliolak AF 704 is a High solids, Sovent-based long-oil alkyd resin recommended for decorative coatings.The resin contains 70% oil Delivery form 85% in D40. |
| PLIOLAK |
PLIOLAK™ AH 832 |
ALK |
Pliolak AH 832 is a Solvent-based long-oil alkyd resin for decorative enamels and varnishes.The resin contains 83% oil .100% solids. |
| PLIOLAK |
PLIOLAK™ AM 342 |
ALK |
Pliolak AM 342 is a Solvent-based short-oil alkyd resin, phenolic and rosin modified for industrial primers and colorful enamels, as well as hammer finishes.Pliolak AM 342 provides fast drying, high hardness, good metal adhesion and chemical resistance.Delivery form 50 % in Xylene |
| PLIOLAK |
PLIOLAK™ AS 245 |
ALK |
Pliolak AS 245 is a Solvent-based short-oil drying alkyd resin based on soya-bean oil.Pliolak AS 245 is specially recommended for the formulation of fast drying enamels, as well as bitumens and anticorrosive primers. It may also be used as plasticizer in combination with melamine resins for stoving enamels as well as with nitrocellulose and also for acid curing lacquers.Pliolak AS 245 is suitable for the formulation of two components clear topcoats for wood furniture, in combination with isocyanates.The 100% resin contains 24 % Oil and 39 % Phthalic Anhydride Delivery form 60 % in Xylene |
| PLIOLAK |
PLIOLAK™ AS 284 |
ALK |
Pliolak AS 284 is a Solvent-based short-oil alkyd resin mainly recommended for industrial enamels, anti-corrosive primers, lacquers and clear topcoats for wood.The resin contains 22% oil and 40% phthalic anhydrid.Delivery form 60% in Xylene |
| PLIOLAK |
PLIOLAK™ AS 622 |
ALK |
Pliolak AS 622 is a Sovent-base long-oil drying alkyd resin based on sunflower oil.Pliolak AS 622 is recommended as a sole binder or in combination with high solids long-oil alkyd resins for the formulation of decorative enamels and varnishes that fulfill the VOC’s (Volatile Organic Compounds) emissions limits defined in the Directive 42/2004/CE.Pliolak AS 622 is especially suitable for the formulation of white enamels.The 100 % resin contains 62 % Oil and 25 % Phthalic Anhydride Delivery form 75 % in Dearomatized White Spirit |
| PLIOLAK |
PLIOLAK™ AS 652 |
ALK |
Pliolak AS 652 is a Solvent-based long-oil alkyd resin that provides good drying time, wrinkling resistance and weathering resistance, with good gloss and color retention.Pliolak AS 652 is used for decorative coatings, including interior and exterior applications.The 100% resin contains 65% oil and 23 % Phthalic Anhydride Delivery form 75 % in Dearomatized White Spirit |
| PLIOLAK |
PLIOLAK™ AU 520 |
ALK |
Pliolak AU 520 is a Solvent-based medium-oil urethane alkyd resin for metal paints.Pliolak AU 520 provides good anti-corrosive properties and adhesion when properly formulated and applied with an appropriate dry film thickness. Use in combination with a long-oil alkyd resin to improve flexibility.The 100% resin contains 52% oil and 18 % Phthalic Anhydride Delivery form 60 % in solvent D40 |
| PLIOLAK |
PLIOLAK™ AU 620 |
ALK |
Pliolak AU 620 is a Solvent-based long-oil urethane alkyd resin for decorative and marine coatings.Pliolak AU 620 provides improved drying time and hardness as well as high resistance to abrasion and saponification.The 100% resin contains 62% oil and 12 % Phthalic Anhydride Delivery form 60 % in solvent D40 |
| PLIOLAK |
PLIOLAK™ AV 303 |
ALK |
Pliolak AV 303 is a Solvent-based short-oil modified alkyd resin for industrial enamels.Pliolak AV 303 provides extremely fast drying even in unfavorable climatic conditions. The 100% resin contains 30% oil. Delivery form 60 % in Xylene. |
| PLIOLITE |
PLIOLITE® AC4 |
OTH |
Pliolite AC4 is a styrene-acrylate copolymer, often used in combination with Pliolite AC80, to form tough abrasion and chemically resistant films that have excellent UV resistance and exterior weathering properties.Solvent based thixotropic resin for low to high textured exterior masonry coatings, primers, anti-corrosion coatings, concrete protection and intumescent coatings. |
| PLIOLITE |
PLIOLITE® AC5-G |
OTH |
Pliolite AC5G is a styrene-acrylate copolymer, often used in combination with Pliolite AC80, to form tough abrasion and chemically resistant films that have excellent UV resistance and exterior weathering properties.Solvent based pseudoplastic resin for low to high build exterior masonry coatings, primers, anti-corrosion coatings, concrete protection and intumescent coatings. |
| PLIOLITE |
PLIOLITE® AC80 |
OTH |
Pliolite AC80, often used in combination with Pliolite AC4 or Pliolite AC5G, forms though abrasion and chemically resistant films that have excellent adhesion, UV resistance and exterior weathering properties.Newtonian resin for exterior masonry coatings, anticarbonation, metal protective and intumescent coatings. |
| PLIOLITE |
PLIOLITE® AC90 |
OTH |
Pliolite AC90 styrene-acrylate copolymer provides excellent water resistence and durability. Its melt rheology and synergy with other intumescent raw materials delivers outstanding char consistency and fire resistance.Newtonian resin for high performance intumescent coatings. |
| PLIOLITE |
PLIOLITE® LV72 |
OTH |
Pliolite LV 72 is a low viscosity styrene-acrylate copolymer with high pigment binding properties that forms tough, abrasion and alkali resistant films with excellent adhesion to concrete and steel, and with very good water and chemical resistance.Newtonian resin giving low viscosity solutions, with very good sprayability, for formulation of swimming pool paints and as a replacement for chlorinated rubber. |
| PLIOLITE |
PLIOLITE® S6B |
SB-Dry |
High styrene butadiene resin with a typical styrene/butadieneratio of 83 / 17 |
| PLIOLITE |
PLIOLITE® S6H |
SB-Dry |
High styrene butadiene resin with a typical styrene/butadiene ratio of 82.5 / 17.5 |
| PLIOLITE |
PLIOLITE® VTAC-L |
OTH |
Pliolite VTAC-L is a highly soluble, vinyl toluene-acrylate copolymer that forms tough, durable films with excellent adhesion to concrete and steel, with very good water and chemical resistance.Newtonian resin soluble in mineral spirits, for formulation of flat or textured masonry coatings, alkali resistant primers, anticorrosion paints and intumescent coatings. |
| PLIOTEC |
PLIOTEC™ 115 |
PVAC |
Pliotec 115 is a vinyl-acetate resin with excellent adhesion to polyurethane foam and other substrates. It imparts fast drying and ease of application to intumescent coatings used on non-metallic substrates.Water-borne resin for intumescent coatings for PU foams. |
| PLIOTEC |
PLIOTEC® 7104E |
SA |
Pliotec 7104E is high Tg styrene acrylic latex that provides excellent adhesion to concrete and resistance to chemicals. It allows formulation of floor coatings that exhibits superior resistance to abrasion and hot tire pick-up.Pliotec 7104E can be used to formulate garage floor coatings, masonry primers and waterproofing sealers. |
| PLIOTEC |
PLIOTEC® CR30 |
SA |
Pliotec CR30 self-crosslinking styrene acrylic latex provides excellent chemical resistance, and is suitable for low VOC concrete floor paints.Water-based self-crosslinking resin for garage, basement and laundry room floor paints. |
| PLIOTEC |
PLIOTEC® CR78 |
SA |
Pliotec CR78 self-crosslinking styrene acrylic latex provides excellent chemical resistance, and superior hot-tire pick-up resistance, suitable for low VOC garage floor paints.Water-based styrene acrylic resin for garage floor paints and institutional wall coverings. |
| PLIOTEC |
PLIOTEC® CS24 |
SA |
Pliotec CS24 is a water-based modified acrylic and adipic acid dihydrazide-free binder recommended for High gloss wood trim paints.It provides excellent blocking and cracking resistance with high gloss capability. |
| PLIOTEC |
PLIOTEC® EL25 |
PA |
Pliotec EL25 acrylic elastomeric latex provides excellent tensile/elongation properties, superior dirt pick-up resistance, great adhesion to concrete und UV resistance.Water-based elastomeric resin for vertical masonry coatings, roofing and tilt up coatings. |
| PLIOTEC |
PLIOTEC™ HDT12 |
SA |
Modified styrene-acrylic copolymer latex based on Hydrophobic Dispersion Technology, with excellent adhesion to metals, and superior water resistance, delivering corrosion protection even without the use of anticorrosive pigments.Pliotec HDT12 is recommended for Direct-To-Metal (DTM) coatings, from high gloss enamels to anticorrosive primers. |
| PLIOTEC |
PLIOTEC® HDT16 |
SA |
Pliotec HDT16 modified styrene-acrylic copolymer latex provides excellent water and corrosion resistance, fast hardness development and superior adhesion to a wide variety of substrates (ferrous and non-ferrous metals, ceramic tiles, PVC and more).Water-based resin for anti-corrosion paints and primers, Direct-To-Metal (DTM) coatings and multi-surface renovation paints. |
| PLIOTEC |
PLIOTEC® LEB18 |
SA |
Pliotec LEB18 is unique modified styrene-acrylic copolymer latex that ensures superior resistance to exudation (surfactant leaching) and efflorescence, with balanced dirt pick-up resistance and crack bridging ability. Thanks to its stabilisation system, Pliotec LEB 18 demonstates enhanced early rain resistance.Water-based resin for flat or high build masonry paints, topcoats for EIFS and house plinths, all-weather paints. |
| PLIOTEC |
PLIOTEC® LEB20 |
PA |
Pliotec LEB20 is pure acrylic copolymer that ensures superior resistance to exudation (surfactant leaching) and efflorescence, with excellent color retention, strong early rain resistance, and superior dirt pick-up resistance.Unique water-based resin for exterior masonry paints, topcoats for EIFS and house plinths, all-weather paints. |
| PLIOTEC |
PLIOTEC® LEB22 |
PA |
Pliotec LEB20 is pure acrylic copolymer that ensures superior resistance to exudation (surfactant leaching) and efflorescence, with excellent color retention, strong early rain resistance, and superior dirt pick-up resistance.Unique water-based resin for exterior masonry paints, topcoats for EIFS and house plinths, all-weather paints. |
| PLIOTEC |
PLIOTEC® PA05 |
PA |
Pliotec PA05 pure acrylic latex with high Tg provides excellent resistance to water, UV and chemicals, very good adhesion to concrete, and hot-tire pick-up resistance.Water-based resin for high performance coatings, concrete sealers and interior/exterior floor paints. |
| PLIOTEC |
PLIOTEC® PA90 |
PA |
Pliotec PA90 pure acrylic latex provides excellent water and blush resistance, very good weathering and UV resistance, and low coalescing demand.Water-based resin for pigmented coatings, stains, aggregate binders, and vertical clear coatings. |
| PLIOTEC |
PLIOTEC® PA90MT |
PA |
Pliotec PA90MT is pure acrylic copolymer that provides excellent water and blush resistance, very good weathering and UV resistance, and low coalescing demand.Pliotec PA90MT is designed for formulation of water-based high performance coatings, concrete stains, and for vertical or horizontal architectural paints. |
| PLIOTEC |
PLIOTEC® SA40 |
SA |
Pliotec SA40 is styrene acrylic copolymer that provides excellent adhesion to concrete and outstanding resistance to alkali and efflorescence.Pliotec SA40 is designed to formulate water-based waterproofing sealers, masonry primers, and concrete cure-and-seal products. |
| PLIOTEC |
PLIOTEC® SC105 |
PA |
Pliotec SC105 self-crosslinking pure acrylic latex provides excellent early water resistance, very good hot tire pick-up resistance, and adhesion to concrete, tile, and wood.Self-crosslinking resin for concrete and tile sealers, deck coatings, and porch & floor coatings. |
| PLIOTEC |
PLIOTEC® SC203 |
PA |
Self-crosslinking
all-acrylic latex, imparting excellent blush resistance and adhesion to
multiple substrates including concrete and tile. It forms a durable film with
good hot tire pick-up resistance.
Pliotec SC203 is recommended for clear concrete sealers
and floor coatings. It can be formulated into <50 g/L VOC coatings. |
| PLIOWAY |
PLIOWAY® EC1 |
OTH |
Plioway EC1 is a vinyl-acrylate copolymer soluble in low odour, dearomatized aliphatic solvents. It provides excellent adhesion on a wide variety of substrates, as well as outstanding stain blocking properties.Newtonian resin for low odour, stain blocking primers, waterproofing sealers, correction fluids and intumescent coatings. |
| PLIOWAY |
PLIOWAY® ECT |
OTH |
Plioway ECT is a partially crosslinked, vinyl-acrylate copolymer, soluble in low odour, dearomatized aliphatic solvents, mainly used in combination with Plioway EC1, eliminating the need for external thickeners which can often be detrimental to film performance.Rheological resin for formulation of low odour stain blocking primers, water proofing sealers, correction fluids and intumescent coatings. |
| PLIOWAY |
PLIOWAY™ ULTRA 200 |
OTH |
Plioway Ultra 200 is a vinyl-acrylate copolymer soluble in odourless isoparaffinic solvents, that forms non-yellowing, tough coatings with excellent adhesion and stain blocking properties.Highly soluble Newtonian resin for formulation of odourless stain blocking primers, basement water proofing sealers, correction fluids and intumecent coatings. |
| PLIOWAY |
PLIOWAY® ULTRA 350LV |
OTH |
Plioway Ultra 350LV is a vinyl-acrylate copolymer, soluble in odourless isoparaffinic solvents, that form tough, non-yellowing with excellent adhesion and stain blocking properties.Low viscosity Newtonian resin for formulation of odourless stain blocking primers, basement water proofing sealers, correction fluids, and intumescent coatings. |
| PLIOWAY |
PLIOWAY® ULTRA G20 |
OTH |
Plioway Ultra G20 is a vinyl-acrylate copolymer, soluble in odourless isoparaffinic solvents and used in combination with Plioway Ultra 200 or Ultra 350LV, eliminating the need for external thickeners which can often be detrimental to film performance.Pseudoplastic rheological resin for formulation of odourless stain blocking primers, basement water proofing sealers, correction fluids and intumescent coatings. |
| POLYFOX |
POLYFOX™ PF-136A |
OTH |
Anionic fluorinated (CF3) polyether diammonium sulfate for aqueous formulationsPolyFox PF-136A wetting, flow and leveling agent is suitable for use in a wide variety of aqueous coating, floor finish, and ink applications. |
| POLYFOX |
POLYFOX™ PF-151N |
OTH |
50 % active Nonionic fluorinated (C2F5) polyether ethoxylatedPolyFox PF-151N wetting, flow and leveling agent is suitable for use in a wide variety of aqueous coating, ink, and electronics applications. |
| POLYFOX |
POLYFOX™ PF-154N |
OTH |
25 % active Nonionic fluorinated (C2F5) polyether ethoxylatedPolyFox PF-154N wetting, flow and leveling agent is suitable for use in a wide variety of aqueous coating, ink, and electronics applications. |
| POLYFOX |
POLYFOX™ PF-156A |
OTH |
Anionic fluorinated (C2F5) polyether diammonium disulfate for aqueous formulations.PolyFox PF-156A wetting, flow and leveling agent is suitable for use in a wide variety of aqueous coating, floor finish, and ink applications. |
| POLYFOX |
POLYFOX™ PF-159 |
OTH |
100 % active Nonionic fluorinated (C2F5) polyether ethoxylatedPolyFox PF-159 highly efficient wetting, flow and leveling agent is suitable for use in a broad variety of aqueous, solvent, 100% solid coating, ink, and adhesive applications. |
| POLYFOX |
POLYFOX™ PF-2002 |
OTH |
Anionic fluorinated (C2F5) polyether diammonium disulfate for aqueous formulationsPolyFox PF-2002 wetting, flow and leveling agent is designed for US DfE compliant floor finish applications |
| POLYFOX |
POLYFOX™ PF-2003 |
OTH |
Anionic fluorinated (CF3) polyether diammonium disulfate for aqueous formulationsPolyFox PF-2003 wetting, flow and leveling agent is designed for US DfE compliant floor finish applications. |
| POLYFOX |
POLYFOX™ PF-6320 |
OTH |
Solvent soluble diol functional fluorinated (CF3) polyether diol terminated PolyFox PF-6320 wetting, flow and levelig agent or reactive intermediate is suitable for solvent based industrial and maintenance coatings, adhesives, electronics, and lubricants. |
| POLYFOX |
POLYFOX™ PF-636 |
OTH |
Solvent soluble diol functional fluorinated (CF3) polyether diol terminatedPolyFox PF-636 wetting, flow and leveling agent or reactive intermediate is suitable for solvent based industrial and maintenance coatings, adhesives, electronics, and lubricants. |
| POLYFOX |
POLYFOX™ PF-652-NF |
OTH |
50% active solvent soluble fluorinated (C2F5) ethoxylate A-B-A tri-block copolymerPolyFox PF-652-NF wetting, flow and leveling agent or reactive intermediate is suitable for solvent based industrial and maintenance coatings, adhesives, and litho plate coatings. |
| POLYFOX |
POLYFOX™ PF-6520 |
OTH |
Solvent soluble diol functional fluorinated (C2F5) polyether diol terminatedPolyFox PF-6520 wetting, flow and leveling agent or reactive intermediate is suitable for solvent based industrial and maintenance coatings, adhesives, electronics, and lubricants. |
| POLYFOX |
POLYFOX™ PF-656 |
OTH |
Solvent soluble diol functional fluorinated (C2F5) polyether diol terminatedPolyFox PF-656 wetting, flow and leveling agent or reactive intermediate is suitable for solvent based industrial and maintenance coatings, adhesives, electronics, and lubricants. |
| REVACRYL |
REVACRYL™ AE 3020 |
SA |
REVACRYL AE 3020 is an aqueous dispersion of an acrylic ester-styrene copolymer. The dispersion contains an anionic emulsifier system and is free from film forming aids, APEO, solvents and plasticizers.REVACRYL AE 3020 is a low MFFT silane-modified styrene-acrylic with excellent wet adhesion and water-resistance. It shows high flexibility and is recommended for roof-coatings. |
| REVACRYL |
REVACRYL™ AE 3020 |
SA |
REVACRYL AE 3020 is a finely dispersed, aqueous dispersion of an acrylic ester-styrene copolymer designed for construction applications including waterproofing and ceramic tile adhesives. The dispersion contains an anionic emulsifier system and is free from film forming aids, solvents and plasticizers. |
| REVACRYL |
REVACRYL™ AE 3020 JA |
SA |
A soft Styrene Acrylic coploymer dispersion with excellent elastomeric and crackbridging properties. Revacryl 3020 is silinated hence posses excellent water resistance. It is suitable for a variety of roofing applicationsRevacryl AE 3020JA is recommended for roof coatings, 1K waterpoofing membranes, CTA, caulks and sealants. |
| REVACRYL |
REVACRYL™ AE 3723 |
SA |
Finely dispersed, aqueous dispersion of a acrylic ester-styrene copolymer. The dispersion contains an anionic emulsifier system, is free from film forming aids, APEO, solvents, plasticizers and ammonia.REVACRYL AE 3723 is a low MFFT styrene-acrylic dispersion with very low VOC content (< 300 ppm) and low residual monomer content. It is highly recommended for interior and exterior wallpaints, especially low emission and ecolabel compliant products. It shows a good exterior durability and high saponification resistance. |
| REVACRYL |
REVACRYL™ AE 3723 |
SA |
REVACRYL AE 3723 is a finely dispersed, aqueous dispersion of
an acrylic ester-styrene copolymer for construction applications including tile adhesives. REVACRYL AE 3723 contains an anionic emulsifier system and is free from film forming aids, APEO, solvents, plasticizers and ammonia. It has a very low VOC content (< 300 ppm) and is highly recommended for ecolabel compliant products. |
| REVACRYL |
REVACRYL™ AE 3737 |
SA |
Finely dispersed, aqueous dispersion of an acrylic ester-styrene copolymer. The dispersion contains an anionic emulsifier system, is free from film forming aids, APEO, solvents, plasticizers, and ammonia.REVACRYL AE 3737 is a low MFFT styrene-acrylic dispersion with high water-resistance, excellent wet adhesion and good flexibility. It is highly recommended for ETICS-primers and renders. |
| REVACRYL |
REVACRYL™ AE 3737 |
SA |
REVACRYL AE 3737 is a finely dispersed, aqueous dispersion of an acrylic ester-styrene copolymer designed for construction applications including waterproofing and ceramic tile adhesives.The dispersion contains an anionic emulsifier system and is free from film forming aids, solvents, plasticizers and ammonia. |
| REVACRYL |
REVACRYL™ AE 3820 |
SA |
Finely dispersed, aqueous dispersion of a acrylic ester-styrene copolymer. The dispersion contains an anionic emulsifier system, is free from film forming aids, APEO, solvents, plasticizers and ammonia.REVACRYL AE 3820 is a low MFFT styrene-acrylic dispersion. It is highly recommended for interior and exterior wallpaints. It shows a good scrub-resistance and exterior durability. It is suitable for silicone paints and renders. |
| REVACRYL |
REVACRYL™ AE 4522 |
SA |
REVACRYL AE 4522 is a standard MFFT modified styrene-acrylic dispersion. It shows excellent wet adhesion and high water- and blocking resistance.REVACRYL AE 4522 is highly recommended for adhesion primers on ETICS and mineral substrates. |
| REVACRYL |
REVACRYL™ AE 4522 |
SA |
REVACRYL AE 4522 is a specially modified, aqueous dispersion of a styrene-acrylic ester copolymer for waterproofing and tile adhesive applications. The polymer is engineered for excellent wet adhesion.REVACRYL AE 4522 contains an anionic emulsifier system and is free from film forming aids, solvents and plasticizers. |
| REVACRYL |
REVACRYL™ AE 4530 |
SA |
REVACRYL AE 4530 is a specially modified, aqueous dispersion of a styrene-acrylic ester copolymer intended to achieve good wet adhesion. The dispersion contains an anionic emulsifier system and is free from film forming aids, solvents, plasticizers, and ammonia. |
| REVACRYL |
REVACRYL™ AE 4620 JA |
SA |
Styrene Acrylic dispersion with highly thixotropic rheology profile. It has excellent adhesion to masonary substrates and deliveres good overall performaces in matt to semi gloss architectural coatingsRevacryl 4620JA is recommended for primers, matt and semi gloss coatings and is also suitable for textured coatings |
| REVACRYL |
REVACRYL™ AE 4625 |
SA |
Finely dispersed, aqueous dispersion of an acrylic ester-styrene copolymer. The dispersion contains an anionic emulsifier system, is free from film forming aids, APEO, solvents, plasticizers and ammonia.REVACRYL AE 4625 is a standard MFFT styrene-acrylic dispersion. It shows good exterior durability and very good blocking- and water-resistance. It is highly recommended for exterior wallpaints. Due to high saponification resistance it is suitable for silicate paints. |
| REVACRYL |
REVACRYL™ AE 4625 |
SA |
REVACRYL AE 4625 is a finely dispersed, aqueous dispersion of
a styrene-acrylic ester copolymer. The dispersion contains an
anionic emulsifier system and is free from film forming aids,
solvents, plasticizers and ammonia. |
| REVACRYL |
REVACRYL™ AE 6030 |
SA |
Finely dispersed aqueous dispersion of a styrene-acrylic ester copolymer. The dispersion contains an anionic emulsifier system and is free from film forming aids, APEO, solvents and plasticizers.REVACRYL AE 6030 is a hydrophobic styrene-acrylic dispersion. It shows an excellent adhesion to various metal substrate and a high water-resistance. It is highly recommended for anti-corrosive primers and non-decorative metal monocoats. |
| REVACRYL |
REVACRYL™ AG 203 |
SA |
REVACRYL AG 203 is an anionic stabilised aqueous dispersion of a styrene acrylic copolymer, suitable for agricultural applications. |
| REVACRYL |
REVACRYL™ AG 204 |
SA |
REVACRYL AG 204 is an ammonia free aqueous dispersion of a styrene-acrylic copolymer that is suitable for agricultural applications. |
| REVACRYL |
REVACRYL™ DESIGN 1425 |
SA |
REVACRYL Design 1425 is a finely dispersed, aqueous dispersion of an acrylic ester-styrene copolymer. The dispersion contains an anionic emulsifier system and is free from film forming aids, solvents and plasticizers. |
| REVACRYL |
REVACRYL™ DESIGN 1690 |
SA |
REVACRYL Design 1690 is a finely dispersed, aqueous dispersion of an acrylic ester-styrene copolymer. The dispersion contains an anionic emulsifier system and is free from film forming aids, solvents and plasticizers. |
| REVACRYL |
REVACRYL™ DS 2100 |
SA |
Revacryl DS 2100 is an ammonia free, water-based dispersion of a styrene-acrylic copolymer. It can be used in a broad range of coating applications with well-balanced performance envelope.It's suitable for formulation of indoor mat, silk and semi-gloss paints and Masonry facade paints, with or without silicone emulsion. |
| REVACRYL |
REVACRYL™ L 3752 |
SA |
REVACRYL L 3752 is an APEO-free, anionic, aqueous styrene-acrylic copolymer dispersion. |
| REVACRYL |
REVACRYL™ L 3783 |
SA |
REVACRYL L 3783 is an anionic stabilised aqueous dispersion
of a styrene-acrylic copolymer.
REVACRYL L 3783 is suitable for a wide range of interior and
exterior wall applications. |
| REVACRYL |
REVACRYL™ L 3790 |
SA |
Revacryl L 3790 is an ammonia free, water-based dispersion of styrene-acrylic copolymer, suitable for a wide range of interior and exterior coating applications.The very high binding power and good resistance to water, saponification, alkaline and weathering of Revacryl L 3790 make it a multipurpose product. |
| REVACRYL |
REVACRYL™ L 8761 |
SA |
REVACRYL L 8761 is a anionic acrylic ester and styrene copolymer for various construction applications like ceramic tile adhesives. |
| REVACRYL |
REVACRYL™ P 7600 |
SA |
Revacryl P 7600 is a water-based styrene acrylic copolymer developed for Elastomeric Wall and Roof coatings.It is also recommended for Texture coatings and Silicate paints.Revacryl P 7600 provides high elongation at break, low water uptake and effective water impermeability. |
| REVACRYL |
REVACRYL™ P 7602 |
SA |
Revacryl P 7602 is a plasticizer-free water-based dispersion based on acrylic acid esters and styrene.Revacryl P 7602 is recommended for the manufacturing of Elastomeric Wall and Roof coatings. It is also suitable to produce Resin-bound plasters, Textured coatings and Silicate paints and Plasters. |
| REVACRYL |
REVACRYL™ P 7693 |
SA |
Revacryl P 7693 is a water-based dispersion based on acrylic acid esters and styrene, APEO and ammonia free.Revacryl P 7693 is a new generation binder specially developed for the formulation of high PVC interior paints. It may also be used to manufacture Exterior paints. |
| REVACRYL |
REVACRYL™ P 7699 |
SA |
Revacryl P 7699 is a plasticizer-free water-based dispersion based on acrylic acid esters and styrene.Revacryl P 7699 is especially suitable for manufacturing paints with low VOC content, from Mat to Semi-gloss interior paints, as well as the deep shade paints.Revacryl P 7699 allows the formulation of paints without the need of coalescing agents to reduce the minimum film formation temperature. It can also be used as a binder for the formulation of aqueous primers. |
| REVACRYL |
REVACRYL™ 246 |
SA |
Styrene-acrylic copolymer dispersion with fine
particle size and excellent water and weather weather resistance. It includes self
crosslinking system and exhibits outstanding adhesion to concrete surfaces. It
is suitable as an universal binder for variety of architectural applicationsRevacryl 246 is recommended for primers, high PVC paints,
egg shell to semi gloss finish, roof coatings and textures |
| REVACRYL |
REVACRYL™ R 245 |
SA |
REVACRYL R 245 is a fine particle size, surfactant stabilised
aqueous dispersion of a styrene and methacrylic ester-acrylic ester copolymer. REVACRYL R 245 offers excellent alkali resistance and water resistance with very high pigment binding characteristics. REVACRYL R 245 is recommended for high quality interior and exterior paints. REVACRYL R 245 is also suitable in the following applications: - Ready mixed fillers and ceramic tile adhesives - Cartridge applied Caulks/sealants and building adhesives. |
| REVACRYL |
REVACRYL™ R 387 |
SA |
REVACRYL R 387 is a surfactant stabilised, acrylic/styrene copolymer dispersion. REVACRYL R 387 is free from APEO. |
| REVACRYL |
REVACRYL™ R 4332 |
SA |
REVACRYL R 4332 is a styrene-acrylic polymer dispersion based on APEO free surfactants. It does not contain any added formaldehyde or ammonia. Designed for a wide range of primer and finish coatings applications. |
| REVACRYL |
REVACRYL™ R 4352 |
SA |
REVACRYL R 4352 is a styrene-acrylic polymer dispersion based on APEO free surfactants.Designed for a wide range of paint applications, REVACRYL R 4352 typically has lower odor than conventional styrene-acrylic, therefore very suitable for interior primer sealer or finish. Can be used for formulating premium or high PVC coatings. |
| REVACRYL |
REVACRYL™ R 4370 |
SA |
REVACRYL R 4370 is a styrene-acrylic polymer dispersion based on APEO free surfactants It has good binding capability to be formulated as a premium or high PVC primer or finish. |
| REVACRYL |
REVACRYL™ R 4389 |
SA |
REVACRYL R 4389 is a high solids, styrene acrylic polymer dispersion which displays a highly flexible yet water resistant film. |
| REVACRYL |
REVACRYL™ R 478 |
SA |
REVACRYL R 478 is a styrene acrylic copolymer dispersion containing antifoam. |
| REVACRYL |
REVACRYL™ RM 4550 |
SA |
REVACRYL RM 4550 is a specially modified, aqueous dispersion of a styrene-acrylic ester copolymer. The dispersion is free from film forming aids, APEO, solvents and plasticizers. REVACRYL RM 4550 shows excellent adhesion on mineral substrates and water-resistance. It is highly recommended for road marking paints. |
| REVACRYL |
REVACRYL™ UG 1876 |
SA |
Ammonia free anionic stabilised aqueous dispersion of a styrene-acrylic copolymer. The dispersion is free from film forming aids, APEO, solvents and plasticizers. REVACRYL UG 1876 is low MFFT, low odour styrene-acryyl dispersion. It is designed to function especially in high pH biocide free coating formulations and is extremely stable with silicates. It shows an excellent water-resistance and high scrub resistance. |
| REVACRYL |
REVACRYL™ UG 2311 |
SA |
Ammonia free anionic stabilized aqueous dispersion of a styrene acrylic
copolymer. The dispersion is free from film forming aids, APEO, solvents and
plasticizers.REVACRYL UG 2311 is low MFFT styrene acrylic dispersion with an improving
of dirt pick up resistance. The dispersion is recommended for exterior and
interior masonry coatings. |
| REVACRYL |
REVACRYL™ ULTRAFINE 4210 |
SA |
REVACRYL UltraFine 4210 is a fine particle sized aqueous
dispersion of a styrene acrylic copolymer.
It is suitable for both interior and exterior applications
where its ability to penetrate makes it an excellent vehicle for the deep
priming of substrates.
|
| REVACRYL |
REVACRYL™ ULTRAFINE 4210 |
SA |
REVACRYL UltraFine 4210 is a fine particle sized aqueous dispersion of a styrene-acrylic copolymer recommended for mortar and waterproofing applications. |
| REVACRYL |
REVACRYL™ X 9045 |
SA |
REVACRYL X 9045 is preserved against bacterial and fungal attack. In the manufacture of finished products, the material has to be retreated, as usual, with suitable biocides to give enhanced preservation. |
| REVERSOL |
REVERSOL™ 7330 |
ALK |
Reversol 7330 is a urethane alkyd, modified
with soya oil. It has excellent durability,
colour and gloss retention. |
| ROHAGIT |
ROHAGIT™ 409 |
OTH |
Hydrophobic acrylate copolymer for the formulation of waterproof coatings and binders |
| ROHAGIT |
ROHAGIT™ 417 |
OTH |
Water-based, FDA compliant sizing agent that provides repellent performance |
| ROHAGIT |
ROHAGIT™ A 422 R |
PA |
ROHAGIT A 422 R is a hydrophobically modified alkali swellable rheology modifier (HASE). ROHAGIT A 422 R in its initial emulsion form is an anionically stabilised, low viscosity, aqueous dispersion of a highly carboxylated acrylic copolymer. In the presence of ammonia or another base, ROHAGIT A 422 R is converted to a high viscosity polymer solution (pH 7 -10.5). and plasticizers. |
| ROHAGIT |
ROHAGIT™ SD 15 |
PA |
Finely dispersed aqueous dispersion of a thermoplastic methacrylic acid-acrylic ester copolymer, anionic stabilised. The dispersion is free from APEO, film forming aids, solvents and plasticizers.ROHAGIT SD 15 is a pure acrylic universal ASE-thickener for pH-range > 8.0. It is UV stable and shows an excellent efficacy and is easy to incorporate. The consistency is pasty, not thready. |
| ROHAGIT |
ROHAGIT™ SD 9523 |
XSBR |
Rohagit SD 9523 is an anionic water based dispersion of a butadiene acrylate copolymer. |
| SEQUAPEL |
SEQUAPEL™ 409 |
OTH |
Hydrophobic acrylate copolymer for the formulation of waterproof coatings and binders |
| SEQUAPEL |
SEQUAPEL™ 417 |
OTH |
Water-based, FDA compliant sizing agent that provides repellent performance |
| SUNBOND |
SUNBOND™ 140N |
VA |
Soft and compatible binder for disposable nonwovens, such as hygiene, wipes, and medical apparel |
| SUNBOND |
SUNBOND™ 939 |
PVAC |
Carboxylated PVAc Homopolymer |
| SUNCRYL |
SUNCRYL™ 2555 |
PA |
Silicone-acrylic hybrid release coating |
| SUNCRYL |
SUNCRYL™ CR 152 |
VACO |
Release coating for multi-purpose creped paper masking tape applications |
| SUNCRYL |
SUNCRYL™ CR 4-42 |
PVAC |
Release coating for multi-purpose creped paper masking tape applications |
| SUNIGUM |
SUNIGUM™ P2100 |
ACR |
Terpolymer designed for elastomeric modification of PVC and plastic goods |
| SUNIGUM |
SUNIGUM™ P95 |
ACR |
Acrylate terpolymer partitioned with calcium carbonate |
| SYNOVUS |
SYNOVUS™ |
NBR |
SyNovus is a new nitrile technology offered by Synthomer. It is designed with proprietary cross-linking to optimize barrier protection performance of the final dipped gloves. With this proprietary technology, it is therefore able to be cured at much lower temperature than conventional latex and require no sulfur and accelerator. |
| SYNOXOL |
SYNOXOL™ BEPD |
OTH |
2-Butyl-2-Ethyl-1,3-PropanediolWhite crystalline solidDiol containing primary hydroxyl groupsThe product is FDA approvedCAS number: 115-84-4EC (EINECS) number: 204-111-7HS number: 2905 39 |
| SYNOXOL |
SYNOXOL™ BEPD70L |
OTH |
BEPD 70L is a mixture of 2-Butyl-2-Ethyl-1,3-Propanediol (BEPD), Neopentyl Glycol and waterClear and colourless liquid at room temperatureDiol containing primary hydroxyl groupsCAS number: 115-84-4, 126-30-7, 7732-18-5EC (EINECS) number: 204-111-7, 204-781-0, 231-791-2 HS number: 3824 99
|
| SYNTHEBOND |
SYNTHEBOND™ 1090 |
PA |
Synthebond 1090 is a styrene acrylic emulsion designed for use as laminating adhesive or in heat seal applications. |
| SYNTHEBOND |
SYNTHEBOND™ 7656 |
PA |
Synthebond 7656 is an acrylic emulsion polymer designed for formulating pressure sensitive adhesives for UL181B HVAC tapes. It demonstrates high cohesion and good instant peel. |
| SYNTHEBOND |
SYNTHEBOND™ 7703 |
PA |
Synthebond 7703 is coater ready acrylic pressure sensitive adhesive designed for clear label applications. |
| SYNTHEBOND |
SYNTHEBOND™ 7915 |
PA |
Synthebond 7915 is a pressure sensitive adhesives for permanent graphics applications that need plasticizer migration resistance. |
| SYNTHEBOND |
SYNTHEBOND™ AC 112 |
PA |
Synthebond AC 112 is a self cross-linking acrylic based emulsion designed for use as a soft hand finish on a variety of substrates |
| SYNTHEBOND |
SYNTHEBOND™ AC 1878 |
PA |
General purpose film-forming self-crosslinking acrylic polymer |
| SYNTHEBOND |
SYNTHEBOND™ AC 236 |
PA |
Synthebond AC 236 is a non-yellowing, APE-free, self cross linking acrylic based emulsion, designed for use as a firm hand finish on a variety of substrates |
| SYNTHEBOND |
SYNTHEBOND™ AC 3158 |
VACO |
Hydrophobic acrylate copolymer for the formulation of waterproof coatings and binders |
| SYNTHEBOND |
SYNTHEBOND™ AC 40 |
PA |
SYNTHEBOND AC 40 is a self cross linking acrylic latex used as a binder and textile hand builder with a stiff abrasion resistant finish. |
| SYNTHEBOND |
SYNTHEBOND™ AC 61192 |
PA |
Acrylic binder for nonwovens and textiles applications |
| SYNTHEBOND |
SYNTHEBOND™ E 1020 |
PA |
Synthebond E 1020 is an acrylic emulsion designed for use as a primer or topcoat for paper and film. |
| SYNTHEBOND |
SYNTHEBOND™ E 1030 |
PA |
Synthebond E 1030 is a high acid-value latex capable of dissolving in ammonia to give high viscosity adhesives. |
| SYNTHEBOND |
SYNTHEBOND™ E 1031 |
PA |
Synthebond E 1031 is a high acid-value latex capable of dissolving in ammonia to give high viscosity adhesives. |
| SYNTHEBOND |
SYNTHEBOND™ E 2150 |
PA |
Synthebon E 2151 is a high solids acrylic polymer for use in a variety of high performance adhesive and caulk applications. |
| SYNTHEBOND |
SYNTHEBOND™ E 2800 |
PA |
Synthebond E 2800 is an acrylic copolymer emulsion designed as a high solids pressure sensitive adhesive. |
| SYNTHEBOND |
SYNTHEBOND™ E 3000 |
PA |
Synthebond E 3000 is a styrene-acrylic copolymer emulsion. |
| SYNTHEBOND |
SYNTHEBOND™ E 4010 |
PA |
Synthebond E 4010 is a styrene acrylic copolymer of use in a variety of adhesive applications. |
| SYNTHEBOND |
SYNTHEBOND™ E 6022 |
PA |
High solids acrylic copolymer for use in a variety of high-performance caulks, sealants, adhesives, and coating applications. |
| SYNTHEBOND |
SYNTHEBOND™ E 6030 |
PA |
Synthebond E 6030 is an all acrylic copolymer emulsion designed as a high solids laminating adhesive for construction and HVAC applications. |
| SYNTHEBOND |
SYNTHEBOND™ E 6090 |
SA |
Synthebond E 6090 is a high solids acrylic copolymer for use in a variety of high performance caulks, selants, adhesives and coating applications. |
| SYNTHEBOND |
SYNTHEBOND™ EDF |
OTH |
Synthebond EDF is a proprietary APE-free, polymer formulated specifically for slasher dyeing applications in upholstery and mattress ticking fabrics |
| SYNTHEBOND |
SYNTHEBOND™ L 4805 |
PA |
Synthebond L 4805 is an aqueous acrylic polymer dispersion, which does not contain APEO. It s a pressure sensitive adhesive designed for use in various paper and filmic label applications. |
| SYNTHEBOND |
SYNTHEBOND™ PRIME 7501 |
PA |
Synthebond Prime 7501 is a coater ready acrylic emulsion polymer formulated for applications where high shear and high temperature resistance is needed. |
| SYNTHEBOND |
SYNTHEBOND™ PRIME 7525 |
PA |
Synthebond Prime 7525 is a coater ready acrylic emulsion polymer for applications where good
low surface energy bonding is needed. |
| SYNTHEBOND |
SYNTHEBOND™ PRIME 7526 |
PA |
Synthebond Prime 7526 is a coater ready acrylic emulsion polymer
for applications where good low surface energy bonding is needed
|
| SYNTHEBOND |
SYNTHEBOND™ RW-42ND |
PVAC |
SYNTHEBOND RW-42ND is an APE-free, vinyl acetate copolymer, binder for various applications including hand builder, fabric stabilization, and edge gum |
| SYNTHEBOND |
SYNTHEBOND™ SA 114 |
SA |
Synthebond SA 114 is a medium Tg, APE-free, styrene acrylic dispersion recommended as a general purpose coating and fabric finishing binder |
| SYNTHEBOND |
Synthebond™ SA 126 |
SA |
Synthebond SA 126 is a self cross linking acrylic based emulsion, designed for use as a soft hand finish on a variety of substrates.Synthebond SA 126 provides a very soft film while maintaining satisfactory flexibility and noncracking properties. Synthebond SA 126 is currently being used on polyolefin roofing material and general textile hand modifier. |
| SYNTHEBOND |
Synthebond™ SA 134 |
SA |
Synthebond SA 134 is a soft styrene acrylic emulsion recommended as a general purpose textile back-coating and fabric finishing binder. It has some internal cross-linking and thus provides good wash and dry clean durability. The product exhibits very good water resistance. |
| SYNTHEBOND |
SYNTHEBOND™ SA 223 |
SA |
Synthebond SA 223 is an acrylic based emulsion designed for use as a firm hand finish on a variety of substrates. It provides a firm film while maintaining satisfactory flexibility and noncracking properties. Synthebond SA 223 is currently being used on pleated lamp shades and filtration media, paper bonding and general textile hand modifier. |
| SYNTHEBOND |
SYNTHEBOND™ SA 4096D |
SA |
Self-crosslinking styrene acrylic binder for nonwovens and textiles applications |
| SYNTHEBOND |
SYNTHEBOND™ SP 254 |
OTH |
Synthebond SP 254 is an aqueous dispersion containing 30% polyester polymer solids designed to enhance tensile strength, rigidity and moldability of nonwoven substrates |
| SYNTHEBOND |
SYNTHEBOND™ TFM |
OTH |
SYNTHEBOND TFM is a stable aqueous dispersion of a high molecular weight linear polyester resin for use as a textile warp size, to size filament polyester yarns or to act as a binder with starch and PVA to size polyester/cotton blends |
| SYNTHEBOND |
SYNTHEBOND™ VA 939 |
PVAC |
Carboxylated PVAc Homopolymer |
| SYNTHEBOND |
SYNTHEBOND™ VC 140N |
VA |
Soft and compatible binder for disposable nonwovens, such as hygiene, wipes, and medical apparel |
| SYNTHEBOND |
SYNTHEBOND™ XA 2207 |
PA |
Synthebond XA 2207 is an aqueous acrylic polymer dispersion, which does not contain APEO. It s a coater ready pressure sensitive adhesive
designed for use in various paper and filmic label applications. |
| SYNTHESIZE |
SYNTHESIZE™ TFM |
OTH |
Synthesize TFM is a stable aqueous dispersion of a high molecular weight linear polyester resin for use as a textile warp size, to size filament polyester yarns or to act as a binder with starch and PVA to size polyester/cotton blends |
| SYNTHOMER |
SYNTHOMER™ 6328 |
NBR |
SYNTHOMER 6328 is an aqueous, colloidal dispersion of carboxylated butadiene-acrylonitrile copolymer with a medium acrylonitrile level. The dispersion contains an emulsifier system and is stabilized with an antioxidant. |
| SYNTHOMER |
SYNTHOMER™ 6329 |
NBR |
SYNTHOMER 6329 is an aqueous, colloidal dispersion of carboxylated butadiene-acrylonitrile copolymer with a medium acrylonitrile level. The dispersion contains an emulsifier system and is stabilized with an antioxidant. |
| SYNTHOMER |
SYNTHOMER™ 6330 |
NBR |
SYNTHOMER 6330 is an aqueous, colloidal dispersion of carboxylated butadiene-acrylonitrile copolymer with a medium acrylonitrile level. The dispersion contains an emulsifier system and is stabilized with an antioxidant. |
| SYNTHOMER |
SYNTHOMER™ 6338 |
NBR |
SYNTHOMER 6338 is an aqueous, colloidal dispersion of carboxylated butadiene-acrylonitrile copolymer with a high acrylonitrile level. The dispersion contains an emulsifier system and is stabilized with an antioxidant |
| SYNTHOMER |
SYNTHOMER™ 6628 |
NBR |
SYNTHOMER 6628 is an aqueous, colloidal dispersion of carboxylated butadiene-acrylonitrile copolymer with a high acryonitrile level. The dispersion contains an emulsifier system and is stabilized with an antioxidant. |
| SYNTHOMER |
SYNTHOMER™ NX 795 |
OTH |
2,2,4-Trimethyl-1,3-pentanediol-monoisobutyrate Isobutyric acid, monoester with 2,2,4-trimethylpentane-1,3-diolCAS number: 25265-77-4EC (EINECS) number: 246-771-9 |
| SYNTHOMER |
SYNTHOMER™ NX 800 |
OTH |
1-Isopropyl-2,2-dimethyltrimethylene diisobutyrateTrimethyl Pentanyl DiisobutyrateCAS number: 6846-50-0EC (EINECS) number: 229-934-9 |
| SYNTHOMER |
SYNTHOMER™ X6311 |
NBR |
SYNTHOMER X6311 is an aqueous, colloidal dispersion of carboxylated butadiene-acrylonitrile copolymer with a medium acrylonitrile level. The dispersion contains an emulsifier system and is stabilized with an antioxidant. |
| SYNTHOMER |
SYNTHOMER™ X6322 |
NBR |
SYNTHOMER X6322 is an aqueous, colloidal dispersion of carboxylated butadiene-acrylonitrile copolymer with a medium acrylonitrile level. The dispersion contains an emulsifier system and is stabilized with an antioxidant. |
| SYNTHOMER |
SYNTHOMER™ X6617 |
NBR |
SYNTHOMER X6617 ia an aqueous, colloidal dispersion of carboxylated butadiene-acrylonitrile copolymer with a high acrylonitrile level. The dispersion contains an emulsifier system and is stabilized with an antioxidant. |
| SYNTHOMER |
SYNTHOMER™ X6810 |
NBR |
SYNTHOMER X6810 is an aqueous, colloidal dispersion of carboxylated butadiene-acrylonitrile copolymer with a medium acrylonitrile level. The dispersion contains an emulsifier system and is stabilized with an anitoxidant. |
| SYNTHOMER |
SYNTHOMER™ XVT-LA |
NBR |
SYNTHOMER XVT-LA is an aqueous, colloidal dispersion of a carboxylated butadiene-acrylonitrile copolymer with a medium acrylonitrile level. The dispersion contains an emulsifier system and is stabilized with an antioxidant. |
| VELVETOL |
VELVETOL™ 1471 |
SatPE |
Velvetol 1471 is a multifunctional hydrophilic polyester polymer. While polyester fabrics offer a good substrate in terms of tensile strength and anti-crease properties, their hydrophobic nature, poor conductivity making static build up causes discomfort to human body when used as apparel material. Hydrophilic polyester technology has made it possible to finish polyester fabric that is cotton like, transports moisture and is easy to clean. Velvetol 1471 imparts that finish to polyester fabric in both exhaust and pad cure process without sacrificing key properties of the fabric. |
| VELVETOL |
Velvetol™ 251C |
SatPE |
Velvetol 251C is a multifunctional polyester polymer. It imparts a hydrophilic soft hand finish to polyester fabrics that reduces static charge generation on fabric and garments. |
| VELVETOL |
VELVETOL™ HLC |
OTH |
Lubricant for nonwovens, textiles, and paper applications. |
| Wingstay |
Wingstay™ 29A |
OTH |
Wingstay 29A liquid amine antioxidant is highly effective and can be used directly or after being emulsified for latex applications. Wingstay 29A provides synthetic rubber and mineral oils with excellent protection against oxygen attack, preventing product degradation especially at high temperatures. |
| Wingstay |
Wingstay™ 29A Powder |
OTH |
Wingstay 29A Powder 70% actives amine antioxidant on inert silica facilitates product handling in rubber compounding applications. Wingstay 29A Powder protects rubber-based materials against oxygen attack and prevents product degradation, especially at high temperatures. |
| Wingstay |
Wingstay™ L Flakes |
OTH |
Wingstay L Flakes antioxidant is highly effective and can be used directly, or after being pre-dispersed or emulsified for latex applications. Wingstay L Flakes offers excellent protection against oxygen attack and prevents product degradation and discoloration during processing and storage. |
| Wingstay |
Wingstay™ L Powder |
OTH |
Wingstay L Powder antioxidant is highly effective and can be used directly, or after being pre-dispersed or emulsified for latex applications.Wingstay L Powder offers excellent protection against oxygen attack and prevents product degradation and discoloration during processing and storage. |
| Wingstay |
Wingstay™ SP |
OTH |
Wingstay SP liquid antioxidant is cost-effective and can be used directly or after being emulsified for latex applications. Wingstay SP provides synthetic rubber, as well as rubber-based materials like foams and adhesives, with protection against oxygen attack during manufacturing. |
| Wingstay |
Wingstay™ SP Powder |
OTH |
Wingstay SP Powder 70% actives phenolic antioxidant on inert silica facilitates product handling in rubber compounding applications. Wingstay SP Powder protects rubber materials against oxygen attack, and prevents product degradation and discoloration during processing and storage. |
